Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in July 2025.
The most recent job was on July 12, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
- Contacted homeowner via phone call as a courtesy to confirm homeowner is ready for appointment and to verify address. - I’m gonna stated that he was 20 minutes away, driving from Little Elm, and that he would meet me at the address.. - while waiting for homeowner to arrive performed AC diagnostics on outdoor/condenser. Noticed fan running compressor wasn’t running. - Further diagnostics proved that failure of the contactor (pitted closed) has compromised operations. - homeowner authorized the provided estimate for contactor replacement and VIP annual maintenance agreement enrollment. - replace contactor secured all low/high voltage wiring. Tightened all connections. - Performed minor AC/cooling diagnostic. - Checked all electrical components and amp draws. - Checked refrigerant charge. - Dain Lines not retaining water. - Delta temperature drop across the coil 18°F - Thermostats/zone controller/dampers communicating properly. - System currently cooling, draining, functioning prop
Arrived on site, customer stated that unit was continuously running this morning and then around 1 the thermostat was not powered/wouldn’t run. Customer had breakers off initially. Checked wire connections and everything seemed tight. No water in the float switch. Noted thermostat was original and not from our install. Flipped breakers and everything powered on and began cooling. Allowed unit to run for about an hour with no issues. Measured supply temps around 55 degrees. Measured start amps and found that they were reading high. Also found significant burning on the condenser contactor. Recommended replacement to customer to avoid system failure. Marc elected to keep the contactor for now and had a soft start kit on hand he intended to install. Discussed with Marc that the issue must have been with the thermostat, as there are no other circuit boards in the unit that would cause this. Marc had a thermostat on hand as well and would perform the wiring himself.
Upon arrival compressor not functioning. Performed AC cooling diagnostic and found failed 45/7.5 capacitor. System has expired 5 year parts warranty. Installed replacement capacitor Ran minor AC diagnostics. 20x25x1 filter decent. Checked electrical components. Refrigerant charge is within/at manufacturers operating specifications Temperature is 17°F System is currently functioning cooling draining properly at this time. Annual maintenance recommended ASAP to treat drain lines, clean coils, etc. Technician will have office/dispatch reach out to homeowner to schedule the annual maintenance.. Filter Sizes: Downstairs: 20x25x1 Upstairs: 16x25x1 Recommended high-efficiency filters 20 x 25 x 4“ 16 x 25 x 4“
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Measured high start amps on condenser. This is an indication that the unit is pulling more power than is good for the unit. This could be due to fluctuations in the power grid. Over time this will lead to excessive wear and tear on the unit. I discussed adding a hard start kit to the unit to pr
I arrived at the home because of buyers concern that the unit was not cooling properly. When I arrived that unit was off and not running. I turned both thermostat on and the unit immediately turned on. I measured refrigerant pressures and temperatures coming from the indoor unit. I can only assume that the outdoor compressor had gone into some type of safety lockout. We discussed how restricted airflow to the upstairs zone could contribute to the lockout as well as the location of the air temperature sensor. I modified the ductwork and relocate the sensor. I did also top off the unit with refrigerant. The system is now cooling with a 20° drop. And it has ran for over an hour without any issues. System is cooling properly on departure. Add refrigerant to system Relocate Discharge air temperature sensor And adjust existing ductwork to allow proper airflow to the upstairs zone It is also advised to keep the upstairs thermostat set-point 2/3° higher than downstairs because of the natur
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Measured high start amps initially, but upon further testing we could not reproduce it. Advised customer that a hard start kit would help prolong the life of the system. She stated she did not have the funds at the moment. System in good working order upon departure.
I arrived at our clients home for a single system maintenance inspection. I began by visually inspecting the indoor attic unit. Our client provided white vinegar to be used with the Total C drain cleaner and I poured both of them down the drain line to help prevent clogging. I then proceeded outside to test and inspect the condenser unit. I found a capacitor that is testing below manufacture specifications. This is subsequently causing the compressor to have extremely high start amps. I rinsed the outdoor coils and measured the run amps they tested better once the coils were clean and the system could operate more efficiently. I showed Tamra what I had found regarding the outdoor equipment. We discussed replacing the capacitor and potentially adding a compressor saver to help reduce the high start amps on the compressor. She requested an estimate and will monitor the equipment for now. The unit is cooling properly on departure but our client is aware the capacitor may fail with risi
Upon arrival met homeowner in driveway. We asked if it was ok to park in driveway and if we were blocking anyone. Performed AC maintenance/diagnostics. Changed both filters 20 x 25 x 1” and dated for today. Checked: all electrical components, low & high voltage wiring/sheathing, motors/amp draw, blower wheel cleanliness, treated drain lines, evaporator coil cleanliness, temperature drop across coil(20 degrees Fahrenheit), capacitor, Contactor, & refrigerant charge. Found high voltage to indoor air handler no properly installed through housing and requires electrical fitting(code/saftey/electrical fire hazard) System currently cooling/draining/ functioning properly at this time. Leaving estimate to install electrical fitting for high voltage at air handler.
Arrived at our client home to preform a single system maintenance inspection and preform the quality control check. I began by answer questions regarding the thermostat. I helped our clients connect the thermostat to Wi-Fi and connected the Lennox home app on their cell phones to the thermostat. We walked through different settings and discussed how to best use the thermostat to ensure the home is comfortable. I then proceeded outside to test and measure the refrigerant pressures on the system. I found the unit to be low on refrigerant and informed our client I would be adding more to help the unit run properly. I added the Freon and rinsed the outdoor coils as part of today’s maintenance. I also treated the drain line and ensured the unit was cooling properly on departure.
Replaced sensor and reset system. Checked thermostat and saw no errors. Reviewed system operation and found no issues. System in good working order.

