Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in June 2025.
The most recent job was on June 30, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
Part ordered from Lennox in Allen PO# Dunkin1329 Quote# 39982232 4-5 business days for availability. Will contact the home owner when coil is in hand to schedule coil replacement.
I arrived at our clients home for a single system maintenance inspection. Upon arrival our client informed me that the unit was struggling to maintain temperature upstairs. They had recently replaced the air filters for the system and it continued to struggle. I proceeded outside and began to test and inspect the outdoor equipment. The capacitor and contactor tested within normal manufacture specifications. The compressor start amps. We’re over the manufacturer limit. I did also measure the refrigerant pressures and found them to be low. I confirmed this by measuring the temperature drop on the indoor equipment and I only measured 6/7° drop. I proceeded to wash the outdoor coils and called Mr Norman to discuss my findings. I informed him that the unit was low and no longer under manufacture warranty. His options were to add refrigerant and an additional leak sealant or a full system replacement. He elected to add the refrigerant and leak sealant or a today. I stressed that this was
I performed a single system cooling maintenance. I checked amps, capacitor, filter, cleanliness, drains, and safeties. Also, I investigated a loud noise when the outdoor unit starts and a humidity issue. I turned on the overcool function to allow the system to better pull humidity. As for the loud noise, I tried replacing the hard start capacitor. It did not change the noise. I unwired the hard start and tested it. The unit is reasonably when starting. I asked the customer to accompany me outside to get his opinion. He confirmed that is quieter. I informed him about the start lock out that Amana units are notorious for. I told him I would come by and wire it back in, if it becomes an issue. The indoor unit could use its blower and evaporator coil cleaned to remove stress on the system. Due to the amount of rust present on the motor shaft, it is classified as a level 2 cleaning. This will cause me to spend more time taking it apart. REMOVE AND CLEAN BLOWER ASSEMBLY LEVEL 2 A BLOWER A
I arrived at the property to inspect the partially installed HVAC system and associated ductwork. The client has expressed concerns regarding the adequacy of the system's capacity for the size of the home. Upon inspection, I verified that the system includes a 5-ton capacity evaporator coil and a 110,000 BTU furnace. At the time of the visit, the outdoor condenser unit had not yet been installed. The proposed living space of the home exceeds 3,000 square feet. I also inspected the ductwork layout in the attic. The supply side utilizes a single mixing box that distributes air to the entire home. Several supply runs exceed 25 feet in length, and there are multiple wye connections that split airflow between different rooms. This configuration may lead to airflow imbalances throughout the home. The return air system also relies on a single mixing box, which serves four bedrooms. Additionally, a “jumper box” located in the hallway is connected to two other rooms, which may further impact
Upon arrival found outside/condenser off and thermostat control not flush to its backplate where low voltage control wire communicates with main control board in equipment. Thermostat was demanding a call for cooling but not communicating with equipment properly. I made sure that the thermostat control was properly flush to the back plate and afterwards system started cooling properly. Performed AC/cooling diagnostics. Found clean 20 x 25 x 1“ air filter and was pointed the right direction. Fresh air control on and functioning properly. System is draining properly and has not retained any water. Checked all electrical components, amp draw, & wiring/sheathing. Refrigerant charge is within manufactures operating specifications. Delta temperature drop across the coil is 17.8°F Condenser coils need to be cleaned. Recommend annual maintenance. System cooling, draining, & functioning properly upon departure.
- WARRANTY COND FAN MTR/ SHIP/PAPERWORK LVL 1 Performed replacement of carrier parts warranty for a condenser fan motor and dual run capacitor. After repairs performed AC diagnostics …. checked all the components and refrigerant charge. Refrigerant charge is within/at manufactures operating specifications. System calls for an 8°F subcool target temperature and is currently providing a 7.5°F sub cool. Maintenance and washing of the outdoor coils will improve heat rejection on the outdoor coils and system will function more efficiently. System is now operational and cooling properly but requires seasonal System requires to have the outdoor condenser coils throughly rinsed with water and drain line needs to be cleared out and treated. Homeowner declined maintenance and clearing of the drain line. Temperature drop across a coil 17.9°F Educated homeowner that it would take two - three hours or even after the sun goes down before it satisfies the set point of 70°F on the thermostat.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Attic is very hot Unit in good working order upon departure.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Found contactor testing outside range 20+amps. Measured high start amps. And fan capacitor was testing a bit low. Replaced capacitor and spoke with Frank about hard start kits and their functionality.
Upon arrival customer stated that unit was not blowing as cool of air as it was. Upon further inspection of the unit we found that the refrigerant was low indicating a leak. We offered leak seal and 7lbs of refrigerant. We preformed cooling maintenance while we were here. We tested the electrical components start and run amps.. all tested within manufacture specifications. Customer went with the leak seal and refrigerant top off. Unit was cooling upon departure No warranty / no guarantee.
Preformed cooling maintenance. Tested run and start amps for all electrical components for outdoor fan and compressor motors. All tested within manufacture specifications. Treated drain line client had filter to change. Filter size 20x25x1. Client stated two rooms plus a closet were not cooling adequately. Upon further inspection we noticed the attic was missing insulation and talked with customer about possibly redesigning ducts and adding a bypass vents to allow the hot air to escape the rooms. Provided estimates for a new breaker disconnect and insulation. Unit cooling upon departure.

