Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX between April 2025 and May 2025.
The most recent job was on May 8, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
Started inspection at the indoor air handler and replaced filter. I noticed a decent amount of dust on the blower wheel which will cause drag shortening the lifespan of the motor. I recommend Pulling out and cleaning the blower wheel to prolong system of life. Blower motor amps were within range. Measure temperature split of 20°. On the outdoor unit, I rinsed the condenser coils as they were very dirty. Contactor was testing high at 19.3 ohms. Capacitor was testing within range. Compressor start and run amps were within range. Fan ramps were written range. System in good working order upon departure.
Performed a 1 system spring maintenance ( heat pump). Tasks performed. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked refrigerant pressures. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw,,,,notice the compressor was drawing over 38 amps rush current when started up,,then 12 amps after,, recommended a hard start kit to help releasing some stress on the compressor was. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirty,, return plenum is dusty ,, recommend a duct cleaning. 11. Inspected evaporator coil. 12. Inspected blower motor/ blower wheel,, both are dusty,, recommended a blower cleaning for better performance. 13. Checked blower amp draw. 14. Measured temperature differential . 15. Inspected drain lines. 16. Washed condenser unit. Found no mo
Performed a 2 system spring maintenance ( heat pump). Tasks performed. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked refrigerant pressures. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirty. 11. Inspected evaporator coil. 12. Inspected blower motor/ blower wheel. 13. Checked blower amp draw. 14. Measured temperature differential . 15. Inspected drain lines. 16. Washed condenser units. We didn’t find any issues/ concerns at this time.
Performed a 1 system spring maintenance ( heat pump). Tasks performed. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections,,, noticed the condenser wire has severe damage and needs to be replaced as soon as possible. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked refrigerant pressures. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirty. 11. Inspected evaporator coil,,,there are some signs of rust underneath. 12. Inspected blower motor/ blower wheel,,, is extremely dirty,, some growth on the blower wiring and buildup on blower wheel. 13. Checked blower amp draw. 14. Measured temperature differential . 15. Inspected drain lines,,,unit doesn’t have any water safety switches installed,,, we noticed they have had water issues in the past and recommended a
Arrived to clients concern that the unit was not cooling. We arrived and I immediately proceeded onto the roof and check the condenser unit. I found the unit to be running properly without any electrical issues. Inside Brayden found the filters to be extremely dirty and partially collapsed. We removed and replaced the air filters and measures the temperature drop in the shop. We measured a 18° drop from the front return to the main supply in the prep area. Our client mentioned he kept the thermostat set to 74° and customers complained that it was hot. We suggested keeping the temperature to 70 or 72° and if that would improve comfort for patrons. The unit is cooling properly on departure.
Arrived to home for concerns of noise coming from the attic. Upon arrival our clients explained to me that the noise was a high pitch sound and almost sounded like an animal. I proceeded to turn the unit on and into the attic. I visually inspected the unit. And could not replicate the sound. I also opened up the flue pipe and found nothing inside of it. The home does have evidence of water surrounding the hot water heater flue pipe and on the ceiling also. Kent is aware of this. I have no evidence to prove the noise was coming from the system and it is currently cooling properly. They will contact a handy man for the other issues we found today.
Arrived to property for the unit not cooling. The tenant moved in a few days ago on Sunday. He noticed the temperature was not dropping and checked the filter. The filter was extremely dirty and causing significant airflow restriction. I proceeded outside and found the compressor to be in a lockout and not coming on. I also tested and found a failed dual capacitor. I called the landlord and we spoke briefly on the bandaid repair that needed to happen to get the unit on. We also discussed price but he was not interested in saving 10% with the maintenance agreement due to him having a work call. I did get verbal authorization to replace the failed capacitor only and will send another estimate for further compressor protection. I did replace the capacitor and further tested the unit. The compressor had extremely high start amps and this is why I am also presenting a compressor saver as an option.
Performed single system cooling maintenance. The system is a 2018 gas system. I checked amps, capacitor, filter, drains, electrical, cleanliness, and temperature differential. The system is mostly performing within manufacture specifications. I spoke with the home owner about some issues that could be addressed. The outdoor unit is matted with build up that water was not enough to remove. The capacitor on the compressor side is out of specs and may not continue to start. The ducts have a bit of build up. This will result in excessive filter changing and added wear on the system because of air restrictions. One of the biggest killers of systems is dust. I provided options to address listed concerns.
With ATMOS. I was able to isolate gas leak to the unit for front of shop. Will need to return to further test gas leak from this unit.
Performed 2 system cooling maintenance. I checked amps, capacitors, filters, drains, electrical, cleanliness, ducts, and safeties. The systems are performing to manufacture specifications. There has been an on going issue with a duct that isn’t properly connected to a supply grill. The customer has approved the work and is scheduled for May 9th 10am - 12pm. This work includes cutting and pulling a little bit of pvc to bring it more flush on the back porch. The items needed for the work are listed on the estimate. Collected 100.00 dollar deposit.

