Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in May 2025.
The most recent job was on May 15, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
Arrived at our clients home for the upstairs unit not cooling properly. The home owner met us outside and showed us the outdoor condenser unit. We immediately connected our gauges and found the compressor not pumping properly. We removed the compressor wires from the contactor and found it to have open windings. We then showed our client our diagnoses and began to discuss a full system replacement due to the fact that the existing unit has R22 refrigerant that is no longer available. Mr Jeffrey asked for a 2 system estimate and we proceeded into the attic to look at the existing ductwork and any particulars that may need to be addressed. Mr Jeffrey did inform us that we were the second AC company out today and he wanted a basic estimate for 2 systems and also a variable speed options for both systems. We discussed the features and benefits of both options as well as the advantages and disadvantages for either option. We did send an email for financing as well. They do have a 3rd AC
Homeowner stated that the outdoor unit was humming sometimes,, that it was a Wei sound. We inspected electrical wiring, tested compressor/ condenser fan motor capacitor,, tested ok, we tested contactor, checked compressor/ condenser fan motor amp draw, checked refrigerant pressures, inspected return filter, measured temperature differential, had 22 degrees split differential,,,unit is performing properly at this time , unfortunately we couldn’t duplicate the issue at this time, we talked about some recommendations for better performance and will send estimates. Estimates include. Blower cleaning,,, it’s very dusty and needs to be clean as soon as possible. Hard start kit,,,,,extends the life on your compressor and drops starting amps. Single pole contactor,,, manufacturer specifications suggest to replace it when reads below 10 and above 20 ohms resistance,,,it’s reading 22 ohms.
Arrived at our clients home for the unit not cooling properly and we turned on the thermostat and verified the inside unit was coming on. We proceeded outside and could hear only the outdoor fan motor coming on. We opened the panel and found a compromised capacitor and burnt wires inside the electrical cabinet. The compressor came on intermittently and we could see the expose raw wire glowing hot. We immediately shut power off and proceeded inside. At the indoor unit we found the evaporator coil extremely restricted due to dust and pet hair that had accumulated over time. We also found the blower motor leaking oil and drawing high amps to preform its function. We brought all our findings to Mr Andrew’s attention and discussed repairs vs replacement. We discussed how repairs would only be temporary due to the excessive stress on the compressor and we could not properly access and clean the evaporator coil. Mr Andrew elected to proceed with a replacement instead and we are scheduled to r
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel-clean 12. Checked blower amp draw. 13. Measured temperature differential. Found to be within range 14. Inspected drain lines and treated to prevent blockages 15. Washed condenser unit.
I performed a single system cooling maintenance. I checked amps, capacitor, filter, electrical, drains, safeties, and cleanliness. The system is performing mostly inside of manufacture specifications. The system could use a primary float switch because of poor drain design. For the current float switch to become tripped, there would need to be 2 clogs. This would result in cost to clear 2 clogs. The switch would allow us to detect a clog before it progresses to a big issue. The supply plenum in the attic is leaking cool air. This reduces efficiency and will cause moisture production. The compressor is currently pulling over its rated per the data tag on the outdoor unit. It is rated to pull under 134amps. It is currently pulling 137.9amps. This will cause damage over time to the compressor. To achieve the full life of the compressor, it is advised to install a hard start kit to reduce the amps back into range.
Performed a 1 system spring maintenance (gas). Tasks performed. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked refrigerant pressures. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirt,,, it’s dusty,,needs to be clean.. 11. Inspected evaporator coil. 12. Inspected blower motor/ blower wheel. 13. Checked blower amp draw. 14. Measured temperature differential . 15. Inspected drain lines,,,were treated,, there was some water inside the emergency drain pan ,, couldn’t find where was coming from,, recommended to install an overflow switch on the main drain line to prevent water damage,, there is one on the emergency drain line. 16. Washed condenser unit.
We returned to our clients home for the unit not cooling properly. We immediately proceeded outside and found the unit to be in a low pressure lockout. Our client had not yet placed the air filter and we discussed how the unit needs an air filter to add some restriction and help the unit preform its proper function. That without the filter the air moves across the coil too quickly and trips the outdoor safety. We reset the outdoor unit and it ran properly for 20+ mins. It then shutoff. I assumed it was the float switch which I had checked but the other technician was outside and corrected me saying it had shutoff prior to me checking the water switch. We then further proceeded to test the outdoor unit. We found that the outdoor defrost control board was getting all the proper voltage to the board and into the safeties but it was not sending signal to the contactor. I immediately showed this to our client and we discussed how this was an intermediate issue and we were lucky to catch i
Insulation board, 6” collar, 5ft of 6” duct, mastic, and metal tap. Cutting and adjusting emergency drain to be more aesthetically pleasing.
We arrived here for the outdoor unit not cooling. Client had the thermostat off upon arrival, we turned the thermostat on. We proceeded outside the out door unit came on immediately. The start amps were very high and had abnormal readings for Freon. After about five minutes of running the unit shut off. We went into the attic and found the water safety switched was tripped. We also found a dirty air filter causing extreme suffocation to the unit. We showed our findings to our client and he elected to install a blowout valve and compressor saver to his system today. Once installed we showed him the work that was preformed and showed him that the components were in manufacture specifications.our client did not have a filter to install, he will purchase an air filter to install immediately and we did leave the unit cooling without an air filter.
Arrived at our clients home for a single system cooling maintenance inspection. We began outside with the condenser unit. We tested and inspected all the electrical components and ensured everything passed today’s inspection. We rinsed the outdoor unit to remove dust and grass debris from the coil today. Once completed we proceeded inside. We found the attic unit to be without a water safety switch. The drain pan had evidence of residue water from the past but no existing rust. We discussed a water safety will shut off the unit if a clog were to occur in the primary drain line. Teresa requested an estimate for a surge protector and also a water safety switch. The unit is cooling properly on departure.

