Frisco has grown faster than almost any city in America over the past two decades, and the homes here reflect it. Larger floor plans, multi-zone systems, high-efficiency equipment, and newer construction in neighborhoods like The Fields, Phillips Creek Ranch, and Viridian. Keeping all of it running well takes an HVAC company that knows what it’s doing. Adon Complete Air Conditioning and Heating has been running calls for HVAC service in Frisco for years from our home base in Anna, just up the Dallas North Tollway corridor. We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer, and we’re available 24 hours a day, 7 days a week for emergencies.
What We Do for Frisco Homeowners
AC Repair. We diagnose and repair all makes and models. Frisco’s newer construction often means multi-zone systems and communicating equipment — our technicians know how to work on all of it.
AC Installation. When it’s time to replace, we size every system correctly using a proper load calculation. That matters especially in Frisco’s larger homes where an improperly sized system will short-cycle and leave rooms uncomfortable. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Frisco homeowners with high-end systems, staying on a maintenance schedule is one of the best ways to protect your investment.
Mini-Split Installation. Garages, home offices, casitas, and bonus spaces are common in Frisco’s larger homes. Mini-splits handle these spaces cleanly without touching your central system.
Heat Pump Installation and Repair. Heat pumps provide both heating and cooling from one system and work well in North Texas’s climate. A practical choice for Frisco homeowners upgrading to a more efficient setup.
Indoor Air Quality. Air filtration systems, UV purifiers, humidifiers, dehumidifiers, and a free “What Are You Breathing?” screening. Frisco’s tight construction means less natural ventilation, making air quality systems more important than in older homes.
Air Duct Cleaning. Even newer ductwork accumulates contaminants over time. Professional duct cleaning improves air quality and keeps your system running efficiently throughout the home.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. In a larger Frisco home, that adds up fast. We inspect, repair, and seal ductwork throughout the area.
Why Frisco Homeowners Choose Adon Complete
Frisco has no shortage of HVAC companies competing for business. Here’s why our customers keep calling us back.
We know multi-zone and communicating systems. The job notes from our Frisco calls show what we actually work on here – damper adjustments, multi-system diagnostics, communicating Trane equipment, humidity management in two-story homes. This isn’t routine work, and we handle it well.
Jesse Villarreal has over 27 years of experience. He’s the owner and is directly involved in how the business operates. When something goes wrong, you’re dealing with a company where the owner’s reputation is on the line.
We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained on the brands most common in Frisco’s newer construction. Full manufacturer warranty on every system we install.
The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access. Straightforward and affordable.
Serving Frisco and Surrounding Collin County Communities
We serve all of Frisco, including The Fields, Phillips Creek Ranch, Viridian, Stonebriar, and the established neighborhoods along Preston Road and the Dallas North Tollway. We also serve the surrounding communities of Allen, McKinney, Anna, Melissa, and Sherman.
Frequently Asked Questions
Here are some common questions we get about our HVAC services in Frisco.
How much does AC repair cost in Frisco, TX?
Most AC repairs in Frisco run between $150 and $600 depending on the type of repair. Frisco’s newer homes often have multi-zone systems and higher-end equipment, which can affect parts costs. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you service multi-zone systems in Frisco?
Yes. Multi-zone systems and communicating HVAC equipment are common in Frisco’s larger homes, and our technicians work on them regularly. We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, and more.
Do you offer HVAC maintenance plans in Frisco?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. Preventive maintenance is especially important for the multi-system setups common in Frisco’s larger homes.
Do you offer emergency HVAC service in Frisco?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Frisco. When you call after hours, you reach a real person who can get a technician to your home fast.
What areas near Frisco do you serve?
We serve all of Frisco and the surrounding communities including Allen, McKinney, Anna, Melissa, and Sherman.
Ready to Get Your System Serviced?
Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online for HVAC services in Frisco. We handle everything from routine maintenance to emergency repairs throughout Frisco and Collin County.
Recent Jobs and Reviews in Frisco, TX
Frisco, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Frisco, TX between November 2024 and April 2025.
The most recent job was on April 7, 2025.
Adon Complete Air Conditioning and Heating has completed 51 jobs in Frisco, TX in the last 12 months. The first job there was in March 2020.
Job Locations
Homeowner stated that they had someone else diagnosing their unit,, they were told the blower motor was out and they just wanted to verify it. We started diagnostic at the indoor unit ( heat pump), thermostat was set to heat, noticed the blower motor going on/ off,, verified high voltage coming in , had 240 v needed to power the blower motor and also verified low voltage (27 volts ) power signal to cool ,, had both verified. Blower motor needs to be replaced,, homeowner is aware that we can’t guarantee proper system operation after blower replacement,, that there might be some other issues .
Homeowner stated that there is a weird smell, specially on one room ( son’s room), there are 2 gas units at this address, both units are from 2006 ,,according to customer they have never been serviced, both units have extremely dirty return plenum/ ductwork, we also noticed blower motors are very dusty and some buildup on blower wheels/ supply vents and return vents are very dirty as well ,,we highly recommended a duct cleaning, blower cleaning,,,we also recommended a thorough inspection on both units ( maintenance),to verify/ inspect all components/ safety switches ( cooling/ heating) are working properly.
Performed a 1 system spring maintenance ( gas). Tasks performed. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor,,,recommended a hard start kit to extend the life on the compressor and also a surge protector to prevent any over current. 6. Checked refrigerant pressures. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirty. 11. Inspected evaporator coil. 12. Inspected blower motor/ blower wheel. 13. Checked blower amp draw. 14. Measured temperature differential . 15. Inspected drain lines., recommended a blow out valve , 16. Washed condenser unit. Unit is cooling properly,, found no issues/ concerns at this time. Will send estimates for recommendations.
Arrived at home for two system heat maintenance inspection. Our client provided filters to be replaced today. After replacing the filters, I proceeded to test and inspect both furnished units. I began by first clean the flame sensor, pressure, switch, ports, and cleaned out the furnace cabinet. I also did a visual inspection on both blower motors and found them to be clean at this time. I tested to ensure that the fire safety for both furnaces were working properly as well as tested inducer and blower motors for each unit. Everything passed inspection today. I discussed protecting equipment with surge protection but our client. Declined at this time. Both units are running properly on departure
Returned to suite due to clients concern of water leaking from ceiling. I found that the return plenum box was not sealed with mastic and all 4 corners of the box were not sealed. These corners correspond with the wet spot on the ceiling tiles. Our client elected to seal the plenum box on the exterior side to help prevent future water leakage. I showed our client pictures and let him know it would take about 48 hours to completely dry. No leaks found on rooftop at this time.
Arrived for single rut heat maintenance inspection. Began by replacing air filters inside the suite for our clients. Once replaced I proceeded to the unit. I tested and checked all electrical components and ensured the electric strip heat was working properly. I found the control board of the unit to have corrosion on it and 2 legs of electric strip heat are very high. The blower motor is also over amping its recommended specification. I showed this to our client and he elected to monitor the unit for now. And potentially replace the entire system when failure occurs. I did I for him that his unit is the only unit without gas heat and upgrading to heat would be an option when replacing the unit.
I arrived for a single system maintenance inspection. The board president informed me of a noise issue from the unit. I began first by doing a visual inspection on the air handler. I found the 22*22*1 filter extremely dirty and restricting airflow. This is causing the unit to make a loud noise due to airflow restriction. I showed this to our client and washed the reusable filter and let it dry completely before reinstalling it. I proceeded to inspect the electric strip heat and ensured all components were operating within manufacture specifications. I found the blower motor to be pulling high amps due to the dust on the blower wheel. I showed this to our client and we discussed cleaning the motor to ensure efficiency and life of the equipment. I then proceeded outside and tested all the electrical components and Freon pressures of the unit. Everything passed inspection today. I did also wash the condenser coil as part of today’s visit. Our client would potentially like to invest in
Preformed system, maintenance check and draw clean condensing coil and indoor unit of any dusting debris. Recommended 1) Blower motor capacitor as it was below the 6% manufacturer recommends replacing. 2) Pull and clean Blower Motor and Fan Blades. 3) 2026 V.I.P. Renewal Maintenance
Preformed 4 system maintenance on 4 single stage gas units all units operating at manufacture spec. No current issues at this time. Recommended pan treatment, and replacement on blower motor.
Performed 2 system heating maintenance. Checked amps, filters, cleanliness, electrical, and safeties. System are performing to manufacture specifications. Provided pricing for noticed issues and spoke with the customer about the end of the year special. Customer is interested in getting pricing to replace two 4 ton gas completes.

