Menu

Heating and Air Conditioning Services in Richardson, TX

Adon Complete Air Conditioning and Heating provides HVAC services in Richardson, TX, running calls throughout Dallas and Collin County from our home base in Anna. Richardson sits right along the border of both counties, and we serve the full city – from the older ranch-style homes near downtown and the University of Texas at Dallas area to the commercial properties along the Telecom Corridor on US-75. Whether your AC goes out in the summer heat or your furnace needs service before a cold front moves through, we’re a straightforward call away.

Richardson’s housing stock skews older than many of the cities we serve, with a lot of homes built in the 1960s, 70s, and 80s that are on their second or third HVAC system. We know these homes well – older ductwork, non-standard configurations, systems that have been patched over the years. We service all makes and models, we’re a Trane Comfort Specialist and Mitsubishi-authorized dealer, and we offer 24/7 emergency service throughout Richardson and the surrounding area.

Schedule HVAC Service in RichardsonCall (903) 482-4900

HVAC Services We Offer in Richardson, TX

AC Repair: Same-day AC repair available throughout Richardson and the surrounding Dallas-Collin County area. We diagnose and repair all makes and models, and most calls are resolved in a single visit. When your air conditioning fails during a Texas summer, we treat it as the emergency it is.

AC Installation and Replacement: Richardson’s older homes are prime candidates for system replacement – an aging unit in a 1970s home working against original ductwork is costing you more every month than a properly sized new system would. We do a full load calculation, size the system correctly, and install it to manufacturer specs. All new installations come with up to a 10-year labor warranty.

Heating Repair and Installation: We service gas furnaces, heat pumps, and electric systems throughout Richardson. Older furnaces in Richardson’s established neighborhoods are one of the more common service calls we get – aging heat exchangers, worn igniters, and cracked flue pipes are all things we catch and repair before they become bigger problems.

HVAC Maintenance: Our Adon Care Club plan is $12 a month and covers two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Richardson homeowners with older systems, regular maintenance is the most cost-effective way to extend equipment life and catch problems early.

Ductless Mini-Split Systems: Older Richardson homes with additions, converted garages, or rooms that were never wired into the main duct system are good candidates for ductless mini-splits. We install single and multi-zone systems and they’re far more efficient than window units for spaces that need year-round comfort.

Heat Pumps: Heat pumps handle both heating and cooling from one system, and in Richardson’s climate – where winters are cold but rarely brutal – they’re a practical, efficient option. We install and service heat pumps throughout Richardson and can help you decide if one makes sense for your home.

Indoor Air Quality: Older Richardson homes can struggle with dust, allergens, and humidity issues that newer construction handles with tighter building envelopes. We offer air filtration systems, UV air purifiers, humidifiers, dehumidifiers, and a free “What Are You Breathing?” screening for Richardson area homeowners.

Duct Cleaning and Duct Repair: In a city with as much older housing stock as Richardson, ductwork is one of the first places we look when a system isn’t performing. Aging ducts leak conditioned air into attics and crawlspaces, drive up energy bills, and create uneven temperatures room to room. We inspect, clean, and seal ductwork throughout Richardson.

Why Richardson Homeowners Choose Adon Complete

Neighborhoods and Areas We Serve in Richardson, TX

We provide HVAC services throughout Richardson, including the neighborhoods near downtown Richardson, the UTD campus area, Canyon Creek, Breckinridge Park, and the commercial corridors along US-75 (Central Expressway) and Campbell Road. We also serve Richardson’s neighboring cities including Plano, Garland, Allen, and McKinney.

Schedule HVAC Service in RichardsonCall (903) 482-4900

Richardson, TX HVAC FAQ

How much does AC repair cost in Richardson, TX?

Most AC repairs in Richardson run between $150 and $600 depending on the type of repair. Simple fixes like a capacitor replacement or refrigerant recharge are on the lower end. More involved repairs like a blower motor or evaporator coil cost more. We give you a clear estimate before any work begins – call (903) 482-4900 to schedule a diagnostic visit.

Do you offer emergency HVAC service in Richardson?

Yes. We offer 24/7 emergency heating and air conditioning service throughout Richardson and the surrounding area. When you call after hours you reach a real person who can get a technician to your home fast.

My Richardson home is older and the AC can’t keep up. Is it worth repairing or should I replace it?

For older homes in Richardson, we look at a few things: the age of the system, the cost of the repair versus a replacement, and whether the existing ductwork is up to handling a new system efficiently. If a system is 15-plus years old and needs a major repair, replacement usually makes more sense. We give free estimates on replacements and honest second opinions on repair-versus-replace decisions.

What HVAC brands do you service in Richardson?

We service all makes and models including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer we have factory-trained expertise on those brands, but we don’t turn down a job because of what brand is on the equipment.

Do you handle commercial HVAC in Richardson?

Yes. Richardson’s Telecom Corridor and business parks are home to a lot of commercial office space, and we handle commercial HVAC service throughout the area. We work with offices, retail spaces, and light commercial properties, and maintenance agreements are available for businesses that want scheduled service and priority response.

Schedule HVAC Service in Richardson, TX Today

Whether you need same-day AC repair, a replacement on an aging system, or want to get on a maintenance plan, Adon Complete Air Conditioning and Heating is ready to help. Call us at (903) 482-4900 or click below to schedule. We also serve the surrounding communities of Plano, Garland, Allen, McKinney, and Wylie.

Schedule HVAC Service in RichardsonCall (903) 482-4900

Recent Jobs and Reviews in Richardson, TX

Rated 5.0 out of 5 stars based on 1 customer reviews

Customers say: The overall sentiment across these reviews is overwhelmingly positive, reflecting strong customer satisfaction and appreciation for the service provided. Customers consistently praise the professionalism, knowledge, and efficiency of the technicians, highlighting their courteous demeanor and thorough explanations of work performed. A recurring theme is the company's responsiveness, with many reviewers expressing gratitude for quick arrival times, same-day or next-day service, and emergency availability during hot weather conditions. The honest, straightforward approach without upselling or gimmicks is frequently mentioned as a standout quality that builds trust. Customers appreciate the clear communication from both technicians and office staff, including timely updates on arrival times. The friendly and patient attitudes of service providers, even in stressful situations, earn particular commendation. Many reviewers indicate they would highly recommend the company and plan to use their services again, with several noting this is their preferred choice after multiple positive experiences. The tone is enthusiastic and grateful, with customers feeling valued and well-served, particularly during urgent situations involving AC failures in extreme heat. Overall, the reviews convey a strong sense of reliability, integrity, and customer-focused service that generates loyalty and satisfaction.

Richardson, TX at a glance

Adon Complete Air Conditioning and Heating has completed 10 jobs in Richardson, TX between April 2026 and July 2026.

The most recent job was on July 15, 2026.

Adon Complete Air Conditioning and Heating has completed 28 jobs in Richardson, TX in the last 12 months. The first job there was in May 2020.

Job Locations

Shelby S.
Shelby S.
I performed a 2 system cooling maintenance on 2022 gas equipment. The upstairs outdoor unit was swapped in 2024. I checked amps, capacitors, filters, electrical, drains, and cleanliness. I replaced the downstairs capacitor during the visit under parts and labor warranty. The Airscrubber cells have burnt out. Also, I offered to add surge protection to the outdoor units. The systems are cooling upon departure.
Richardson, TX 75080
Richardson, TX - I performed a 2 system cooling maintenance on 2022 gas equipment. The upstairs outdoor unit was swapped in 2024. I checked amps, capacitors, filters, electrical, drains, and cleanliness. I replaced the downstairs capacitor during the visit under parts and labor warranty. The Airscrubber cells have burnt out. Also, I offered to add surge protection to the outdoor units. The systems are cooling upon departure.
Richardson, TX - I performed a 2 system cooling maintenance on 2022 gas equipment. The upstairs outdoor unit was swapped in 2024. I checked amps, capacitors, filters, electrical, drains, and cleanliness. I replaced the downstairs capacitor during the visit under parts and labor warranty. The Airscrubber cells have burnt out. Also, I offered to add surge protection to the outdoor units. The systems are cooling upon departure.
Clayton P.
Clayton P.
Upon arrival, contactor was pulled in at condenser. Blower motor was running at the indoor unit. Right away I noticed the start capacitor inside the condenser was swollen. I also noticed that the outdoor unit was extremely dirty and needed a cleaning. Homeowner opted to have the cleaning done as well as the start capacitor replacement. I also offered our VIP service agreement and homeowner agreed to renew. After replacing the capacitor and cleaning the condenser, I tested system and system is running properly at this time.
Richardson, TX 75081
Richardson, TX - Upon arrival, contactor was pulled in at condenser. Blower motor was running at the indoor unit. Right away I noticed the start capacitor inside the condenser was swollen. I also noticed that the outdoor unit was extremely dirty and needed a cleaning. Homeowner opted to have the cleaning done as well as the start capacitor replacement. I also offered our VIP service agreement and homeowner agreed to renew. After replacing the capacitor and cleaning the condenser, I tested system and system is running properly at this time.
Richardson, TX - Upon arrival, contactor was pulled in at condenser. Blower motor was running at the indoor unit. Right away I noticed the start capacitor inside the condenser was swollen. I also noticed that the outdoor unit was extremely dirty and needed a cleaning. Homeowner opted to have the cleaning done as well as the start capacitor replacement. I also offered our VIP service agreement and homeowner agreed to renew. After replacing the capacitor and cleaning the condenser, I tested system and system is running properly at this time.
Brayden W.
Brayden W.
Arrived on site found unit running and holding set point at 71 degrees. No ice found at this time. Upon further observation it was found that the filter was extremely dirty and restricting airflow. Found thermostat set to fan on. This would cause the filter to become dirtier than it otherwise would have in the amount of time. Replaced filter and verified 55 degrees coming out of system. System in good working order upon departure.
Richardson, TX 75080
Richardson, TX - Arrived on site found unit running and holding set point at 71 degrees. No ice found at this time. Upon further observation it was found that the filter was extremely dirty and restricting airflow. Found thermostat set to fan on. This would cause the filter to become dirtier than it otherwise would have in the amount of time. Replaced filter and verified 55 degrees coming out of system. System in good working order upon departure.
Richardson, TX - Arrived on site found unit running and holding set point at 71 degrees. No ice found at this time. Upon further observation it was found that the filter was extremely dirty and restricting airflow. Found thermostat set to fan on. This would cause the filter to become dirtier than it otherwise would have in the amount of time. Replaced filter and verified 55 degrees coming out of system. System in good working order upon departure.
Brayden W.
Brayden W.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Perform maintenance on upstairs unit and QC on downstairs. Added silicone sealant around disconnect. Added
Richardson, TX 75080
Richardson, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Perform maintenance on upstairs unit and QC on downstairs.

Added silicone sealant around disconnect. Added
Richardson, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Perform maintenance on upstairs unit and QC on downstairs.

Added silicone sealant around disconnect. Added
Shelby S.
Shelby S.
I performed a 3 system safety check on 2017 gas communicating systems. I checked amps, filters, electrical, treated the drains, cleanliness, and safeties. When I arrived the living room thermostat was off. Customer stated that it recently started happening. I investigated this issue and did not find a reason for it. I advised that replacement of the thermostat with additional diagnostics may be necessary to figure this issue out. I observed that the systems could use surge protection and upgraded filtration. I offered the options during the time of service.
Richardson, TX 75082
Richardson, TX - I performed a 3 system safety check on 2017 gas communicating systems. I checked amps, filters, electrical, treated the drains, cleanliness, and safeties. When I arrived the living room thermostat was off. Customer stated that it recently started happening. I investigated this issue and did not find a reason for it. I advised that replacement of the thermostat with additional diagnostics may be necessary to figure this issue out. I observed that the systems could use surge protection and upgraded filtration. I offered the options during the time of service.
Richardson, TX - I performed a 3 system safety check on 2017 gas communicating systems. I checked amps, filters, electrical, treated the drains, cleanliness, and safeties. When I arrived the living room thermostat was off. Customer stated that it recently started happening. I investigated this issue and did not find a reason for it. I advised that replacement of the thermostat with additional diagnostics may be necessary to figure this issue out. I observed that the systems could use surge protection and upgraded filtration. I offered the options during the time of service.
Matthew C.
Matthew C.
Preformed single system maintenance on a 2023 trane gas system. I tested all electrical components on the inside unit and all tested within manufacturer specifications. I treated and flushed the drain line with total c and water. Filter did not need to be changed at this time. Duct work could benefit from having a cleaning done. I proceeded outside where I tested all electrical components on the outside unit. All tested within manufacturer specifications. Client has hard start kit and surge protectors. All in good working order. Unit was cooling upon departure.
Richardson, TX 75081
Richardson, TX - Preformed single system maintenance on a 2023 trane gas system. I tested all electrical components on the inside unit and all tested within manufacturer specifications. I treated and flushed the drain line with total c and water. Filter did not need to be changed at this time. Duct work could benefit from having a cleaning done. I proceeded outside where I tested all electrical components on the outside unit. All tested within manufacturer specifications. Client has hard start kit and surge protectors. All in good working order. Unit was cooling upon departure.
Richardson, TX - Preformed single system maintenance on a 2023 trane gas system. I tested all electrical components on the inside unit and all tested within manufacturer specifications. I treated and flushed the drain line with total c and water. Filter did not need to be changed at this time. Duct work could benefit from having a cleaning done. I proceeded outside where I tested all electrical components on the outside unit. All tested within manufacturer specifications. Client has hard start kit and surge protectors. All in good working order. Unit was cooling upon departure.
Matthew C.
Matthew C.
Preformed 2 system maintenance on a 2021 and 2012 gas systems. I tested all electrical components on both systems. All tested within manufacturer specifications. I tested each drain line and treated with totalc and water. The downstairs system could benefit from a duct cleaning. The upstairs condenser unit could benefit from having a hard start kit and condenser cleaning. Both units were cooling upon departure
Richardson, TX 75082
Richardson, TX - Preformed 2 system maintenance on a 2021 and 2012 gas systems. I tested all electrical components on both systems. All tested within manufacturer specifications. I tested each drain line and treated with totalc and water. The downstairs system could benefit from a duct cleaning. The upstairs condenser unit could benefit from having a hard start kit and condenser cleaning. Both units were cooling upon departure
Richardson, TX - Preformed 2 system maintenance on a 2021 and 2012 gas systems. I tested all electrical components on both systems. All tested within manufacturer specifications. I tested each drain line and treated with totalc and water. The downstairs system could benefit from a duct cleaning. The upstairs condenser unit could benefit from having a hard start kit and condenser cleaning. Both units were cooling upon departure
Brayden W.
Brayden W.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Noticed a lot of vines in outdoor unit. I was able to remove the vines without too much trouble as they were
Richardson, TX 75080
Richardson, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Noticed a lot of vines in outdoor unit. I was able to remove the vines without too much trouble as they were
Richardson, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Noticed a lot of vines in outdoor unit. I was able to remove the vines without too much trouble as they were
Brayden W.
Brayden W.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Tree in back yard was starting to grow over the fence and is nearing the outside condenser. Advise cutting
Richardson, TX 75080
Richardson, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

 Tree in back yard was starting to grow over the fence and is nearing the outside condenser. Advise cutting
Richardson, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

 Tree in back yard was starting to grow over the fence and is nearing the outside condenser. Advise cutting
Brayden W.
Brayden W.
Replaced discharge air temp sensor under part and labor warranty. Tested and found. System working as intended. Sensor was showing up now and system was cooling upon departure.
Richardson, TX 75081
Richardson, TX - Replaced discharge air temp sensor under  part and labor warranty. Tested and found. System working as intended. Sensor was showing up now and system was cooling upon departure.

Your High Efficiency

Experts