Menu

Heating and Air Conditioning Services in Anna, TX

Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.

Schedule Service in AnnaCall (903) 482-4900

HVAC Services in Anna, TX

Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:

AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.

AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.

HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.

Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.

Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.

Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.

Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.

Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.

HVAC Services for Anna’s Growing Neighborhoods

Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.

For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.

Why Anna Homeowners Choose Adon Complete

Schedule Service in AnnaCall (903) 482-4900

Frequently Asked Questions

Here are some answers to common questions we get about our Anna HVAC services.

How much does AC repair cost in Anna, TX?

Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.

Do you offer emergency HVAC service in Anna?

Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.

What HVAC brands do you service in Anna?

We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.

Do you offer HVAC maintenance plans in Anna?

Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.

What areas near Anna do you serve?

We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.

Schedule HVAC Service in Anna Today

We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.

Schedule Service in AnnaCall (903) 482-4900

Recent Jobs and Reviews in Anna, TX

Rated 4.9 out of 5 stars based on 67 customer reviews

Customers say: The overall sentiment across these reviews is overwhelmingly positive, reflecting strong customer satisfaction and appreciation for the service provided. Customers consistently praise the professionalism, knowledge, and efficiency of the technicians, highlighting their courteous demeanor and thorough explanations of work performed. A recurring theme is the company's responsiveness, with many reviewers expressing gratitude for quick arrival times, same-day or next-day service, and emergency availability during hot weather conditions. The honest, straightforward approach without upselling or gimmicks is frequently mentioned as a standout quality that builds trust. Customers appreciate the clear communication from both technicians and office staff, including timely updates on arrival times. The friendly and patient attitudes of service providers, even in stressful situations, earn particular commendation. Many reviewers indicate they would highly recommend the company and plan to use their services again, with several noting this is their preferred choice after multiple positive experiences. The tone is enthusiastic and grateful, with customers feeling valued and well-served, particularly during urgent situations involving AC failures in extreme heat. Overall, the reviews convey a strong sense of reliability, integrity, and customer-focused service that generates loyalty and satisfaction.

Anna, TX at a glance

Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in April 2026.

The most recent job was on April 22, 2026.

Adon Complete Air Conditioning and Heating has completed 588 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.

Job Locations

Brayden W.
Brayden W.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Spoke with tech support in order to verify system was properly charged and working as intended. Measured 51
Anna, TX 75409
Anna, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Spoke with tech support in order to verify system was properly charged and working as intended.
Measured 51
Anna, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Spoke with tech support in order to verify system was properly charged and working as intended.
Measured 51
Brayden W.
Brayden W.
Replaced contactor and capacitor to avoid near future system failure. Added hard start kit in order to help compressor run without high start amps. High start amps can happen naturally over time as the compressor becomes worn. Hard start kit help mitigate the start amps in order to prolong compressor life and overall wear and tear on connected electrical components. Also replaced leaky valve core and tested for further leakage and found none. Tested system after installation of electrical comments and found all to be working well. Start amps measured at 30 well within manufacturer specifications. Supply temp of 51 measured. System in good working condition upon departure.
Anna, TX 75409
Anna, TX - Replaced contactor and capacitor to avoid near future system failure. Added hard start kit in order to help compressor run without high start amps. High start amps can happen naturally over time as the compressor becomes worn. Hard start kit help mitigate the start amps in order to prolong compressor life and overall wear and tear on connected electrical components. Also replaced leaky valve core and tested for further leakage and found none.

Tested system after installation of electrical comments and found all to be working well. Start amps measured at 30 well within manufacturer specifications. Supply temp of 51 measured. 

System in good working condition upon departure.
Anna, TX - Replaced contactor and capacitor to avoid near future system failure. Added hard start kit in order to help compressor run without high start amps. High start amps can happen naturally over time as the compressor becomes worn. Hard start kit help mitigate the start amps in order to prolong compressor life and overall wear and tear on connected electrical components. Also replaced leaky valve core and tested for further leakage and found none.

Tested system after installation of electrical comments and found all to be working well. Start amps measured at 30 well within manufacturer specifications. Supply temp of 51 measured. 

System in good working condition upon departure.
Shelby S.
Shelby S.
I performed a 2 cooling maintenance on 2020 gas equipment. I checked amps, capacitors, filters, electrical, cleanliness, drains, and safeties. The systems are performing well overall. I noticed that the unit servicing the bedrooms is needs duct cleaning due to excessive build up in the ducts. I advised upgrading the filtration on this system as well. I offered airscubbers to progress towards more permanent solutions. The capacitors are still in manufacture range, but will likely need change out next visit. The drain for the living room unit is beginning to clog, but is still currently draining. Customer would like to get the duct cleaning, filter upgrade, and drain clearing done. The work is scheduled for 4/24/2026 between 8am - 9am arrival time.
Anna, TX 75409
Anna, TX - I performed a 2 cooling maintenance on 2020 gas equipment. I checked amps, capacitors, filters, electrical, cleanliness, drains, and safeties. The systems are performing well overall. I noticed that the unit servicing the bedrooms is needs duct cleaning due to excessive build up in the ducts. I advised upgrading the filtration on this system as well. I offered airscubbers to progress towards more permanent solutions. The capacitors are still in manufacture range, but will likely need change out next visit. The drain for the living room unit is beginning to clog, but is still currently draining. Customer would like to get the duct cleaning, filter upgrade, and drain clearing done. The work is scheduled for 4/24/2026 between 8am - 9am arrival time.
Anna, TX - I performed a 2 cooling maintenance on 2020 gas equipment. I checked amps, capacitors, filters, electrical, cleanliness, drains, and safeties. The systems are performing well overall. I noticed that the unit servicing the bedrooms is needs duct cleaning due to excessive build up in the ducts. I advised upgrading the filtration on this system as well. I offered airscubbers to progress towards more permanent solutions. The capacitors are still in manufacture range, but will likely need change out next visit. The drain for the living room unit is beginning to clog, but is still currently draining. Customer would like to get the duct cleaning, filter upgrade, and drain clearing done. The work is scheduled for 4/24/2026 between 8am - 9am arrival time.
Brayden W.
Brayden W.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Noticed 1 inch filters installed in system when filter boxes have the capability to take 4 inch filters. Adv
Anna, TX 75409
Anna, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Noticed 1 inch filters installed in system when filter boxes have the capability to take 4 inch filters. Adv
Anna, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Noticed 1 inch filters installed in system when filter boxes have the capability to take 4 inch filters. Adv
Shelby S.
Shelby S.
I performed a single cooling maintenance on a 2021 gas system. I checked amps, capacitors, filters, electrical, drains, and safeties. I informed the customer that the system may be low on refrigerant but it is too early to tell. I advised upgrading the filtration, chemical washing the outdoor unit, and replacing a failing capacitor. Customer wants to wait to upgrade the filtration and chemical washing until they are done with nearby construction. Washing the outdoor unit may be the whole cause for my slightly low temperature split. Customer did not want to move forward with the capacitor at this time.
Anna, TX 75409
Anna, TX - I performed a single cooling maintenance on a 2021 gas system. I checked amps, capacitors, filters, electrical, drains, and safeties. I informed the customer that the system may be low on refrigerant but it is too early to tell. I advised upgrading the filtration, chemical washing the outdoor unit, and replacing a failing capacitor. Customer wants to wait to upgrade the filtration and chemical washing until they are done with nearby construction. Washing the outdoor unit may be the whole cause for my slightly low temperature split. Customer did not want to move forward with the capacitor at this time.
Anna, TX - I performed a single cooling maintenance on a 2021 gas system. I checked amps, capacitors, filters, electrical, drains, and safeties. I informed the customer that the system may be low on refrigerant but it is too early to tell. I advised upgrading the filtration, chemical washing the outdoor unit, and replacing a failing capacitor. Customer wants to wait to upgrade the filtration and chemical washing until they are done with nearby construction. Washing the outdoor unit may be the whole cause for my slightly low temperature split. Customer did not want to move forward with the capacitor at this time.
Shelby S.
Shelby S.
Labor to wire and program new zoning board 4/17/2026 I returned to install the warranty zoning board. I relocated due to it being mounted directly on top of the evaporator coil. The original failure was due to corrosion on the zoning board. I cleaned up the wiring to allow the cover panel to be on. System is cooling upon departure.
Anna, TX 75409
Anna, TX - Labor to wire and program new zoning board 

4/17/2026 
I returned to install the warranty zoning board. I relocated due to it being mounted directly on top of the evaporator coil. The original failure was due to corrosion on the zoning board. I cleaned up the wiring to allow the cover panel to be on. System is cooling upon departure.
Anna, TX - Labor to wire and program new zoning board 

4/17/2026 
I returned to install the warranty zoning board. I relocated due to it being mounted directly on top of the evaporator coil. The original failure was due to corrosion on the zoning board. I cleaned up the wiring to allow the cover panel to be on. System is cooling upon departure.
Matthew C.
Matthew C.
Client called in to provide estimate to have a return grill added to their dining room that is being converted into the office, after thoroughly evaluating the best options to add the return. I provided estimate to have a 10” return cut in the office. Client wants to speak to her husband about it before making any decisions.
Anna, TX 75409
Anna, TX - Client called in to provide estimate to have a return grill added to their dining room that is being converted into the office, after thoroughly evaluating the best options to add the return. I provided estimate to have a 10” return cut in the office. Client wants to speak to her husband about it before making any decisions.
Anna, TX - Client called in to provide estimate to have a return grill added to their dining room that is being converted into the office, after thoroughly evaluating the best options to add the return. I provided estimate to have a 10” return cut in the office. Client wants to speak to her husband about it before making any decisions.
Brayden W.
Brayden W.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Found rat chew hole on connection between coil and filter box. Sealed with mastic and notified homeowner. Fo
Anna, TX 75409
Anna, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Found rat chew hole on connection between coil and filter box. Sealed with mastic and notified homeowner. Fo
Anna, TX - 1. Visually inspected condenser coil for leaks and abnormalities.
2. Inspected condenser fan motor, blades and bearings.
3. Inspected, cleaned, and, tightened wiring connections.
4. Measured capacitance of  compressor/fan motor capacitor.
5. Inspected and measured resistance of contactor
6. Measured compressor current draw.
7. Measured condenser fan motor amp draw.
8. Inspected and replaced return filter.
9. Inspected return plenum for dust or debris.
10. Inspected evaporator coil for cleanliness and oxidation.
11. Inspected blower motor/ blower wheel for dust and debris
12. Measured blower motor current draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Tested drain lines for proper drainage and treated to prevent blockages.
15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris.

Found rat chew hole on connection between coil and filter box. Sealed with mastic and notified homeowner. Fo
Shelby S.
Shelby S.
I performed 2 cooling maintenances on 2016 gas equipment, and they are outside of the warranty. I thoroughly inspected the drains, electrical, cleanliness, performance, filters, and safeties. These systems are in worse shape than last visit. Both units need duct cleaning. The downstairs unit has an active refrigerant leak, a compromised emergency drain pan, a clogged drain line, a filthy blower wheel, and a failing capacitor. The upstairs unit has an active refrigerant leak, a filthy blower wheel, a corroded thermostat, and a failing capacitor. Customer scheduled to have comfort specialist come out same day.
Anna, TX 75409
Anna, TX - I performed 2 cooling maintenances on 2016 gas equipment, and they are outside of the warranty. I thoroughly inspected the drains, electrical, cleanliness, performance, filters, and safeties. These systems are in worse shape than last visit. Both units need duct cleaning.

The downstairs unit has an active refrigerant leak, a compromised emergency drain pan, a clogged drain line, a filthy blower wheel, and a failing capacitor. 

The upstairs unit has an active refrigerant leak, a filthy blower wheel, a corroded thermostat, and a failing capacitor. 

Customer scheduled to have comfort specialist come out same day.
Anna, TX - I performed 2 cooling maintenances on 2016 gas equipment, and they are outside of the warranty. I thoroughly inspected the drains, electrical, cleanliness, performance, filters, and safeties. These systems are in worse shape than last visit. Both units need duct cleaning.

The downstairs unit has an active refrigerant leak, a compromised emergency drain pan, a clogged drain line, a filthy blower wheel, and a failing capacitor. 

The upstairs unit has an active refrigerant leak, a filthy blower wheel, a corroded thermostat, and a failing capacitor. 

Customer scheduled to have comfort specialist come out same day.
Brayden W.
Brayden W.
Came out today for QC visit on new install. Started inside at t-stat (Trane) turned system down to check over unit. System is level all wiring is good no error codes. Getting over 20 degree temp split. Drain line is draining at this time. System is clean and operating as designed. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Tested normal heating operation. Adjusted Lp gas valve to allow a little more gas out. System in good working order upon departure. Thank you for your time.
Anna, TX 75409
Anna, TX -  Came out today for QC visit on new install. Started inside at t-stat (Trane) turned system down to check over unit. System is level all wiring is good no error codes. Getting over 20 degree temp split. Drain line is draining at this time. System is clean and operating as designed. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Tested normal heating operation. Adjusted Lp gas valve to allow a little more gas out. System in good working order upon departure. Thank you for your time.
Anna, TX -  Came out today for QC visit on new install. Started inside at t-stat (Trane) turned system down to check over unit. System is level all wiring is good no error codes. Getting over 20 degree temp split. Drain line is draining at this time. System is clean and operating as designed. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Tested normal heating operation. Adjusted Lp gas valve to allow a little more gas out. System in good working order upon departure. Thank you for your time.

Your High Efficiency

Experts