Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in April 2026.
The most recent job was on April 17, 2026.
Adon Complete Air Conditioning and Heating has completed 588 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
Upon completion of my thorough evaluation, I found that he system is in need of a cleaning on the blower wheel, plenum boxes and duct work. I tested all of the electrical components on the inside unit all were testing within manufacturer specifications. I treated and tested the drain lines with totalc and water. I changed the filter for the client 20x25x4. Temperature being supplied to the home was at 48 degrees with 70 return air. On the outside unit I tested all electrical components, along with start and run amps of the compressor. All tested within manufacturer specifications. I rinsed the outside unit with water. Unit was cooling upon departure.
Upon completion of my thorough evaluation of both systems, I found both can benefit from having a full system deep cleaning done on all major components, along with duct work, this includes the blower wheels, evaporator coils and clearing drain lines. Also the condensers for both units outside could use a deep cleaning as well. The capacitor on the upstairs unit is failing below manufacturer specifications at 30/35 mfd if this part completely goes out he unit will not run until replaced.
I performed a general check of a 2002 heat pump system. I discovered that the indoor unit has heavy rusting on the blower assembly and evaporator coil, the blower cap is bad reading 6.6/7.5, the blower motor bearings are worn out, the unit has an active leak in the Schrader core of the liquid line, the contactor is burnt at the contacts, the outdoor capacitor is bad and reading out of range, and the start amps are high. The indoor unit has a R22 evaporator coil only rated for 300psig, and the outdoor unit is a R410a unit rated for 480psig. With how rusted the evaporator coil is, I fear adding refrigerant may cause the evaporator coil to begin leaking. Repairs needed are: blower assembly/blower wheel/ and blower motor replacement, electrical rebuild of the outdoor unit, evaporator coil cleaning (advise against due to rust and age), and leak repair. Customer wants the information sent over. I did not price the blower assembly/wheel/blower motor during the visit.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Measured capacitance on the capacitor and found it to be testing within range. However, it is now five years
Upon arrival client stated they were hearing s rattling noise come from the attic unit. Upon my thorough inspection. I found that the newly installed Aprilaire filter kit and filter were loose inside and causing the rattle. I tightened everything down and reseated the filter in place.
Upon completion of my thorough evaluation. I found that the manual dampers to the rooms needed to be adjusted to help air flow going to the master bedroom, also i found that the dat sensor is bad. It’s not sending the correct signals to the board telling the board to allow the unit to cool correctly, it is temporarily disconnected to allow the unit to cool. Needs to be changed out for unit to run as intended.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Downstairs unit number two and upstairs unit number one both had capacitors that were testing within manufac
System is a 2022 zoned gas system. Upon arrival, I discovered that the thermostats were not controlling the system. I went into the attic and jumped the system. The system would come on and operate. I tested the zoning board and discovered corrosion on the equipment side. I checked the voltages and determined that the zoning board is bad. I collected a deposit for a warranty zoning board and bypassed it to only use the downstairs thermostat. We will reach out for scheduling once we have the board. System is cooling upon departure.
Upon completion of my thorough evaluation on the outside unit i found that the capacitor to be failing and at end of life. Capacitor is a 45/5 testing at 42.2 minimum allowance us at 42.3. All other electrical components tested within manufacturer specifications. I rinsed the outside unit with water at today’s visit. I tested all electrical components on 5e inside unit. All tested within manufacturer specifications. I changed the filter for the client 20x25x1. Spoke to the client about using a 20x25x4 in instead to allow for longer life of the filter. Also spoke about changing it to a Aprilaire 210 filter client was not interested at this time. I treated and tested drain lines with totalc and water. Temperature supplied to the home was 51 degrees with 73 return air. Unit was cooling upon departure .
House vacant and for sale

