Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in February 2026.
The most recent job was on February 13, 2026.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
Jesse and I arrived and spoke with the homeowner about the rooms that are having air issues. We investigated the ducts at the system and discovered a single damper on the downstairs system. Also, we spoke about upgrading thermostats to allow sensors to be used. We uploaded the notes that were taking during the visit. The upstairs damper are 9, 9, and 7. The downstairs could not be determined, and we will need to bring multiple sizes to address it. There is 5 ducts I can see. The backside of the unit has very limited space.
I performed 2 heating maintenances on 2016 gas systems. I checked amps, filters, electrical, cleanliness, and safeties. I discovered a couple issues and concerns on the equipment. The emergency pan for the upstairs unit is becoming rusted, neither system has a water safety switch, both units have filthy blowers, and the downstairs unit has a faulty high limit switch. I cleaned the dryer vent during the visit and collect. I spoke with the homeowner about my findings, but was not able to go over options to address these areas of concerns. I emailed the options to the customer.
Came out today for QC visit on new install of American standard heat pump. Started inside at t-stat (American standard) and reviewed programming. System is level all wiring is good no error codes. Getting over 100 degree in heating from heat kit and heat pump. Drain line is draining well at this time. System is clean and operating as designed. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Tested normal heating operation and found no issues. Ensured outdoor compartments are properly sealed. Discussed labor warranty and Airscrubber with the homeowner. Homeowner was not interested at this time, but would consider it for the future. System in good working order upon departure. Thank you for your time.
I performed an evaluation on a 2015 heat pump system. I checked amps, filter, electrical, cleanliness, and safeties. I discovered quite a few concerns with the system. The indoor unit is in need of evaporator coil cleaning. A dirty coil causes a higher cost to run the equipment, and stress to the compressor. The system currently does not have a working water safety switch, the low voltage wires rest against the refrigerant and will begin to burn a hole in the wires, and the system really needs duct cleaning. Also, the outdoor unit has notable issues. I noticed that the condensing coil has build up on the back side of the unit. This leads to stress and a higher cost to run the equipment. The unit has a failing capacitor and high starting amps. This is going to directly affect all components in the outdoor unit and may cause the compressor to not start. The contactor has burning present from normal wear and tear. The low voltage wire is exposed and has visual u/v damage to the protectiv
Arrived on site for QC and heating maintenance. On 2025 American standard heat pump. Customer had no questions about thermostat operation or unit operation at this time. However he had noticed that the back children’s rooms tended to be a little colder. Heatpump- heating 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested capacitor and contactor (outdoor electrical) 15. Rinsed condenser unit to promote heat exchange 16. Tested emergency heat and found no issues Found high
Located gas leak coming out of burner log. This indicates that the gas valve is not fully closing and allowing gas to escape when the unit is turned off. This is due to sediment in the gas that can cause various issues. Most municipalities code require a sediment trap to catch sediment and assist in preventing issues like this. Warranty - 90 day Craftsmanship warranty -1 year part warranty Performed blower and evaporator cleaning. Also installed gas valve and sediment trap. Upon completion we throughly tested the unit for functionality/leaks and found no issues. Unit in good working order upon departure.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested for gas leaks 6. Tested functionality and cleaned flame sensor 7. Tested functionality and cleaned pressure switches and ports 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Tested functionality and visually inspected surface igniter 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14.Drain line tested with gallon of water for clogs and to push anything trying to solidify out Found large amount of dust on blower wheel and inside blower cabinet. This indicates that dust is making it past the filter and onto the blower wheel and inevitably the evaporator coil. Which is the next step down the line from the blower wheel. This causes drag on the motor and causes it to work harder an
Provided duct cleaning estimate. Overall the system is in good order and extremely clean. Clients would like to revisit the duct cleaning on her cooling maintenance visit.
Upon arrival client stated that the unit wasn’t cooling Thursday from about 4-9pm. I began my test by placing the unit in a call for cooling. I was getting the 48 degree supply temp, and 68 degree on return. The client also stated that that it smelt like the heat was on when they came home. I tested to see if the heat strips were energized during the cooling mode. No heat strip was energized. I then placed the unit into emergency heat to test the heat strips, I was getting 20 amps across all legs of the heat strips, which tells me they are working properly. I then placed the unit into regular heat mode and after the 5 minute delay the heat mode started heating the house. Supply temp was at 116 and rising durning inspection. All modes were working properly. I did mention to he client the thermostat could be intermittently failing and possibly needs to be replaced. Left estimates for replacement thermostat. Blower wheel is also extremely caked in dust and debris and could benefit from a
Preformed single system heating maintenance on a 2022 gas furnace. I tested all electrical and safety components. All tested within manufacturer specifications. 122 degrees being supplied to the home. Filter upgrade was just installed and did not need to be changed at the time of the inspection. Filter size is Aprilaire 610. I visually inspected the outdoor unit. All was in proper working order. I did mention to the client about some rust build up on the capacitor. Client would like to revisit in the spring maintenance. Unit was heating upon departure

