Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in December 2025.
The most recent job was on December 8, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
I performed a heating maintenance on a 2013 York gas system. I checked amps, filter, electrical, cleanliness, and safeties. I noticed that the units did not have surge protection and that the inducer motor is pulling 1.0amps out of 1.06amps. I brought the inducer motor to the customer attention and they would like to wait before addressing it. I installed 2 surge protectors at the time of service and collected for the work.
Upon arrival, I found that the discharge temperature sensor is faulty and not allowing the system to heat. I removed the sensor from the wiring and the unit came on. This sensor is a safety function for zoning systems to monitor the temperature being supplied from the system. Without this sensor, damage can occur to the system if other issues arise. I installed a replacement sensor and tested the system and found it to be heating great. Customer spoke about hail damage to the condenser fan blade. Customer wanted to wait before joining maintenance program. I noticed a duct that was getting melted by the flue pipe. I adjusted the duct away from the flue pipe.
Arrived on site for dryer vent, cleaning and heating maintenance. Homeowner stated all was well with regards to normal unit operation to his knowledge. Proceeded with heating maintenance as scheduled. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested for gas leaks 6. Tested functionality and cleaned flame sensor 7. Tested functionality and cleaned pressure switches and ports 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Tested functionality and visually inspected surface igniter 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. Noticed decent amount of dust buildup on the blower wheel. This creates drag on the motor, causing the motor to work harder ultimately shortening the lifespan of the motor. Recommend blower wheel clea
Upon arrival client stated that she had water coming from her unit in the attic out of the secondary drain line. Also she stated that her unit for her office was making a loud noise on start up. I began my inspection by pouring water into the main drain line to check for a blockage. The water did not run out of the drain pipe and backed up into the pan indicating a clogged line. I then proceeded to the outside unit were I tested start and run amps along with the electrical components inside the unit. I found that the components were beginning to fail capacitor was reading 32/35 microfaurds, the Contactor was testing at 16 ohms, and the compressor was starting up at over 100 amps. Manufacturer start amps are 62. I left estimates for cleaning the drain line, adding a quick blast valve and Ss1 float switch for the inside unit and new secondary drain pan. Also I left estimates for he compressor saver bundle for the outside unit. Membership was offered for all 3 units. Client would like to
Preformed heat maintenance on a 2019 carrier gas furnace. I tested all electrical components and safeties on the inside unit. All tested within manufacturer specifications. I did find that the ducts were covered in dust along with the plenum boxes. I changed the filter for the client 20x25x4. Temperature being supplied to the home was at 130 degrees and 77 degrees returning to the unit. I proceeded outside to visually inspect the outdoor unit. I did notice that there was some hail damage to the fins. Also I noticed the system did not have any surge protection on it. Client asked if I would take a look at his fireplace vent to see about a replacement, i inspected the vent and it does have some significant hail damage to the outer casing. This is not our area of expertise and I am recommending the client to contact a fireplace repair company. I provided estimates to have all concerns spoke about in today’s visit remedied. Unit was heating upon departure.
I returned to install the warranty 824 thermostat. I programmed and connected the Wi-Fi to it. The phone I needed to connect it to Z-Wave was not available at the time of service. I indicated that the manual will go over the step to connect it.
Arrived on site for heating maintenance on 2022 Lennox furnace. Homeowner stated all was well with regards to normal unit operation to his knowledge. Inquired about dryer vent cleaning and homeowner stated they were not interested at this time. Proceeded with heating maintenance as scheduled. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested for gas leaks 6. Tested functionality and cleaned flame sensor 7. Tested functionality and cleaned pressure switches and ports 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Tested functionality and visually inspected surface igniter 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. All components were testing within range and operating within manufacturer specs. Advised homeowner I was startin
Preformed condenser combing for client. Uploaded before and after pictures of work done.
Arrived on site for heating maintenance on 2023 Trane heat pump. Homeowner stated all is well with regards to normal unit operation. Proceeded with heating maintenance as scheduled. 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested capacitor and contactor (outdoor electrical) 15. Rinsed condenser unit to promote heat exchange 16. Tested emergency heat and found no issues Found high start amps on condenser. Recommend installing hard start kit in order to ease start up of
Preformed work to change out blower motor. Tested blower motor to insure it was in proper operating condition. Blower is functioning properly. Unit was heating upon departure

