Menu

Heating and Air Conditioning Services in Anna, TX

Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.

Schedule Service in AnnaCall (903) 482-4900

HVAC Services in Anna, TX

Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:

AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.

AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.

HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.

Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.

Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.

Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.

Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.

Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.

HVAC Services for Anna’s Growing Neighborhoods

Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.

For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.

Why Anna Homeowners Choose Adon Complete

Schedule Service in AnnaCall (903) 482-4900

Frequently Asked Questions

Here are some answers to common questions we get about our Anna HVAC services.

How much does AC repair cost in Anna, TX?

Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.

Do you offer emergency HVAC service in Anna?

Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.

What HVAC brands do you service in Anna?

We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.

Do you offer HVAC maintenance plans in Anna?

Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.

What areas near Anna do you serve?

We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.

Schedule HVAC Service in Anna Today

We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.

Schedule Service in AnnaCall (903) 482-4900

Recent Jobs and Reviews in Anna, TX

Rated 4.9 out of 5 stars based on 67 customer reviews

Customers say: The overall sentiment across these reviews is overwhelmingly positive, reflecting strong customer satisfaction and appreciation for the service provided. Customers consistently praise the professionalism, knowledge, and efficiency of the technicians, highlighting their courteous demeanor and thorough explanations of work performed. A recurring theme is the company's responsiveness, with many reviewers expressing gratitude for quick arrival times, same-day or next-day service, and emergency availability during hot weather conditions. The honest, straightforward approach without upselling or gimmicks is frequently mentioned as a standout quality that builds trust. Customers appreciate the clear communication from both technicians and office staff, including timely updates on arrival times. The friendly and patient attitudes of service providers, even in stressful situations, earn particular commendation. Many reviewers indicate they would highly recommend the company and plan to use their services again, with several noting this is their preferred choice after multiple positive experiences. The tone is enthusiastic and grateful, with customers feeling valued and well-served, particularly during urgent situations involving AC failures in extreme heat. Overall, the reviews convey a strong sense of reliability, integrity, and customer-focused service that generates loyalty and satisfaction.

Anna, TX at a glance

Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in October 2025.

The most recent job was on October 13, 2025.

Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.

Job Locations

Brayden W.
Brayden W.
Arrived on site for heating maintenance, on 2023 Heatpump and 2025 mini split. 1. Visually inspected condenser coil for debris/ dirty. Found to be pretty dirty with dust and debris 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser units to promote heat exchange 16. Checked heat strips for functionality working as intended.
Anna, TX 75409
Anna, TX - Arrived on site for heating maintenance, on 2023 Heatpump and 2025 mini split.
1. Visually inspected condenser coil for debris/ dirty. Found to be pretty dirty with dust and debris
2. Inspected condenser fan motor.
3. Inspected condenser fan blades.
4. Inspected/ cleaned wiring connections.
5. Tested compressor/ condenser fan motor capacitor.
6. Checked compressor amp draw.
7. Checked condenser fan motor amp draw.
8. Inspected / replaced return filter.
9. Inspected return plenum for debris/ dirty.
10. Inspected evaporator coil.
11. Inspected blower motor/ blower wheel.
12. Checked blower amp draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Inspected drain lines and treated to prevent blockages 
15. Rinsed condenser units to promote heat exchange
16. Checked heat strips for functionality working as intended.
Anna, TX - Arrived on site for heating maintenance, on 2023 Heatpump and 2025 mini split.
1. Visually inspected condenser coil for debris/ dirty. Found to be pretty dirty with dust and debris
2. Inspected condenser fan motor.
3. Inspected condenser fan blades.
4. Inspected/ cleaned wiring connections.
5. Tested compressor/ condenser fan motor capacitor.
6. Checked compressor amp draw.
7. Checked condenser fan motor amp draw.
8. Inspected / replaced return filter.
9. Inspected return plenum for debris/ dirty.
10. Inspected evaporator coil.
11. Inspected blower motor/ blower wheel.
12. Checked blower amp draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Inspected drain lines and treated to prevent blockages 
15. Rinsed condenser units to promote heat exchange
16. Checked heat strips for functionality working as intended.
Jacob P.
Jacob P.
I arrived at our clients home for the upstairs unit not coming on and the thermostat was unresponsive. Our client showed me exactly which thermostat was blank and I proceeded to check voltage. It was not receiving any power. I proceeded upstairs to the attic and diagnosed a failed water safety switch. It had some evidence of water but the drain line was currently empty. I proceeded to replace the failed component under parts and labor warranty. Once replaced I tested the unit to ensure it was working properly. The set point was 78° so I turned it down and confirmed it was cooling properly. Client is only responsible for the dispatch fee today.
Anna, TX 75409
Anna, TX - I arrived at our clients home for the upstairs unit not coming on and the thermostat was unresponsive. Our client showed me exactly which thermostat was blank and I proceeded to check voltage. It was not receiving any power. I proceeded upstairs to the attic and diagnosed a failed water safety switch. It had some evidence of water but the drain line was currently empty. I proceeded to replace the failed component under parts and labor warranty. Once replaced I tested the unit to ensure it was working properly. The set point was 78° so I turned it down and confirmed it was cooling properly.  Client is only responsible for the dispatch fee today.
Anna, TX - I arrived at our clients home for the upstairs unit not coming on and the thermostat was unresponsive. Our client showed me exactly which thermostat was blank and I proceeded to check voltage. It was not receiving any power. I proceeded upstairs to the attic and diagnosed a failed water safety switch. It had some evidence of water but the drain line was currently empty. I proceeded to replace the failed component under parts and labor warranty. Once replaced I tested the unit to ensure it was working properly. The set point was 78° so I turned it down and confirmed it was cooling properly.  Client is only responsible for the dispatch fee today.
Jacob P.
Jacob P.
I arrived to the unit not cooling properly. I proceeded to the thermostat and confirmed it was on and running. The Tenant let me know she had only been in the home for about a week and the system struggled to maintain a 74º set point. I found the filter for the unit to be extremely dirty causing complete air restriction. I then proceeded outside and found the compressor to be partially frozen. I diagnosed a failed capacitor and called Jonathan. I explained my finding to him and we discussed how i needed to replace the capacitor and further test the system to identify if it was low or had a leak. He agreed to replace the capacitor today as well as sign up for our preventative maintenance plan. I replaced the capacitor and proceeded to let the unit run for 15/20 mins. I did identify the unit to be low on refrigerant. I went back inside and proceeded to preform a courtesy leak search. I found the leak on the underside of the evaporator coil. Due to it already being past 5pm on a Friday I
Anna, TX 75409
Anna, TX - I arrived to the unit not cooling properly. I proceeded to the thermostat and confirmed it was on and running. The Tenant let me know she had only been in the home for about a week and the system struggled to maintain a 74º set point.
I found the filter for the unit to be extremely dirty causing complete air restriction. I then proceeded outside and found the compressor to be partially frozen. I diagnosed a failed capacitor and called Jonathan. I explained my finding to him and we discussed how i needed to replace the capacitor and further test the system to identify if it was low or had a leak.
He agreed to replace the capacitor today as well as sign up for our preventative maintenance plan. I replaced the capacitor and proceeded to let the unit run for 15/20 mins. I did identify the unit to be low on refrigerant. I went back inside and proceeded to preform a courtesy leak search. I found the leak on the underside of the evaporator coil.
Due to it already being past 5pm on a Friday I
Anna, TX - I arrived to the unit not cooling properly. I proceeded to the thermostat and confirmed it was on and running. The Tenant let me know she had only been in the home for about a week and the system struggled to maintain a 74º set point.
I found the filter for the unit to be extremely dirty causing complete air restriction. I then proceeded outside and found the compressor to be partially frozen. I diagnosed a failed capacitor and called Jonathan. I explained my finding to him and we discussed how i needed to replace the capacitor and further test the system to identify if it was low or had a leak.
He agreed to replace the capacitor today as well as sign up for our preventative maintenance plan. I replaced the capacitor and proceeded to let the unit run for 15/20 mins. I did identify the unit to be low on refrigerant. I went back inside and proceeded to preform a courtesy leak search. I found the leak on the underside of the evaporator coil.
Due to it already being past 5pm on a Friday I
Brayden W.
Brayden W.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters 17. Tested capacitor and contactor. Contactor was testing within manufacture specs with little to no signs of pitting/burning. Capacitor however was testing low and is 4 years old. Advised replacement to avoid system failure. Homeowner elected to continue to monitor the capacitor as he has a lot
Anna, TX 75409
Anna, TX - 1. Visually inspected condenser coil for debris/ dirty.
2. Inspected condenser fan motor.
3. Inspected condenser fan blades.
4. Inspected/ cleaned wiring connections.
5. Tested compressor/ condenser fan motor capacitor.
6. Checked compressor amp draw.
7. Checked condenser fan motor amp draw.
8. Inspected / replaced return filter.
9. Inspected return plenum for debris/ dirty.
10. Inspected evaporator coil.
11. Inspected blower motor/ blower wheel.
12. Checked blower amp draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Inspected drain lines and treated to prevent blockages 
15. Rinsed condenser unit to promote heat exchange
16. Replaced and dated filters
17. Tested capacitor and contactor. Contactor was testing within manufacture specs with little to no signs of pitting/burning. Capacitor however was testing low and is 4 years old. Advised replacement to avoid system failure. Homeowner elected to continue to monitor the capacitor as he has a lot
Anna, TX - 1. Visually inspected condenser coil for debris/ dirty.
2. Inspected condenser fan motor.
3. Inspected condenser fan blades.
4. Inspected/ cleaned wiring connections.
5. Tested compressor/ condenser fan motor capacitor.
6. Checked compressor amp draw.
7. Checked condenser fan motor amp draw.
8. Inspected / replaced return filter.
9. Inspected return plenum for debris/ dirty.
10. Inspected evaporator coil.
11. Inspected blower motor/ blower wheel.
12. Checked blower amp draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Inspected drain lines and treated to prevent blockages 
15. Rinsed condenser unit to promote heat exchange
16. Replaced and dated filters
17. Tested capacitor and contactor. Contactor was testing within manufacture specs with little to no signs of pitting/burning. Capacitor however was testing low and is 4 years old. Advised replacement to avoid system failure. Homeowner elected to continue to monitor the capacitor as he has a lot
Matthew C.
Matthew C.
Preformed Dryer Vent Cleaning and heating maintenance. I presented all before and after pictures to client. Client was satisfied with the results of the dryer vent cleaning. I started the maintenance by setting up our air advice machine. While that was running i proceeded to Checked all electrical components and safeties on the inside unit. All components tested within manufacturer specifications. Client has apcox and uv light inside the unit in the attic, they are in good working order. I proceeded outside to check the electrical components on the outside unit. The capacitor was testing on the low end of the manufacturer specifications range and the start amps for the compressor were reading 57 max amps out of 72 on the manufacturer. I left estimates to have the compressor saver bundle installed. I also noticed that the unit does not have surge protection. I left estimates for having surge protection installed on the attic unit and the unit outside. Unit was back to cooling upon depar
Anna, TX 75409
Anna, TX - Preformed Dryer Vent Cleaning and heating maintenance. I presented all before and after pictures to client. Client was satisfied with the results of the dryer vent cleaning. I started the maintenance by setting up our air advice machine. While that was running i proceeded to Checked all electrical components and safeties on the inside unit. All components tested within manufacturer specifications. Client has apcox and uv light inside the unit in the attic, they are in good working order. I proceeded outside to check the electrical components on the outside unit. The capacitor was testing on the low end of the manufacturer specifications range and the start amps for the compressor were reading 57 max amps out of 72 on the manufacturer. I left estimates to have the compressor saver bundle installed. I also noticed that the unit does not have surge protection. I left estimates for having surge protection installed on the attic unit and the unit outside. Unit was back to cooling upon depar
Anna, TX - Preformed Dryer Vent Cleaning and heating maintenance. I presented all before and after pictures to client. Client was satisfied with the results of the dryer vent cleaning. I started the maintenance by setting up our air advice machine. While that was running i proceeded to Checked all electrical components and safeties on the inside unit. All components tested within manufacturer specifications. Client has apcox and uv light inside the unit in the attic, they are in good working order. I proceeded outside to check the electrical components on the outside unit. The capacitor was testing on the low end of the manufacturer specifications range and the start amps for the compressor were reading 57 max amps out of 72 on the manufacturer. I left estimates to have the compressor saver bundle installed. I also noticed that the unit does not have surge protection. I left estimates for having surge protection installed on the attic unit and the unit outside. Unit was back to cooling upon depar
Shelby S.
Shelby S.
Upon arrival, I found that the compressor was not turning on. This was due to the compressor side of the capacitor being extremely low on charge. I hooked one up for testing purposes. I performed a thorough evaluation on the downstairs equipment. I noticed some other potential issues. The contactor is ohming at the max of recommended range, the compressor is starting with 68/77 of its allotted amps, and the system is not protected from surges at this time. I prepared options to address all of the noticed potential issues. Customer declined repairs at the time of service, but did sign of for our maintenance agreement.
Anna, TX 75409
Anna, TX - Upon arrival, I found that the compressor was not turning on. This was due to the compressor side of the capacitor being extremely low on charge. I hooked one up for testing purposes. I performed a thorough evaluation on the downstairs equipment. I noticed some other potential issues. The contactor is ohming at the max of recommended range, the compressor is starting with 68/77 of its allotted amps, and the system is not protected from surges at this time. I prepared options to address all of the noticed potential issues. Customer declined repairs at the time of service, but did sign of for our maintenance agreement.
Anna, TX - Upon arrival, I found that the compressor was not turning on. This was due to the compressor side of the capacitor being extremely low on charge. I hooked one up for testing purposes. I performed a thorough evaluation on the downstairs equipment. I noticed some other potential issues. The contactor is ohming at the max of recommended range, the compressor is starting with 68/77 of its allotted amps, and the system is not protected from surges at this time. I prepared options to address all of the noticed potential issues. Customer declined repairs at the time of service, but did sign of for our maintenance agreement.
Matthew C.
Matthew C.
Preformed dryer vent cleaning. Cleaned dryer vent in the attic as vent outlet was located in the roof. Presented client with before and after pictures of the dryer vent. Client was very satisfied with the results.
Anna, TX 75409
Anna, TX - Preformed dryer vent cleaning. Cleaned dryer vent in the attic as vent outlet was located in the roof. Presented client with before and after pictures of the dryer vent. Client was very satisfied with the results.
Anna, TX - Preformed dryer vent cleaning. Cleaned dryer vent in the attic as vent outlet was located in the roof. Presented client with before and after pictures of the dryer vent. Client was very satisfied with the results.
Brayden W.
Brayden W.
Performed heating check up 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Inspected flame sensor and igniter 6. Tested pressure switches and various safeties for functionality 7. Tested normal operation of burners 8. Inspected return filter. Recently replaced by home owner. 9. Inspected return plenum for debris/ dirty. Moderately dirty 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked inducer motor amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Replaced return filter Noticed surge protection on outdoor unit, but not indoor unit. Recommended surge protection to protect entirety of system from surges in power. Unit in good working order upon departure
Anna, TX 75409
Anna, TX - Performed heating check up
1. Visually inspected condenser coil for debris/ dirty.
2. Inspected condenser fan motor.
3. Inspected condenser fan blades.
4. Inspected/ cleaned wiring connections.
5. Inspected flame sensor and igniter
6. Tested pressure switches and various safeties for functionality
7. Tested normal operation of burners 
8. Inspected return filter. Recently replaced by home owner.
9. Inspected return plenum for debris/ dirty. Moderately dirty
10. Inspected evaporator coil.
11. Inspected blower motor/ blower wheel.
12. Checked inducer motor amp draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Inspected drain lines and treated to prevent blockages 
15. Replaced return filter

Noticed surge protection on outdoor unit, but not indoor unit. Recommended surge protection to protect entirety of system from surges in power. 

Unit in good working order upon departure
Anna, TX - Performed heating check up
1. Visually inspected condenser coil for debris/ dirty.
2. Inspected condenser fan motor.
3. Inspected condenser fan blades.
4. Inspected/ cleaned wiring connections.
5. Inspected flame sensor and igniter
6. Tested pressure switches and various safeties for functionality
7. Tested normal operation of burners 
8. Inspected return filter. Recently replaced by home owner.
9. Inspected return plenum for debris/ dirty. Moderately dirty
10. Inspected evaporator coil.
11. Inspected blower motor/ blower wheel.
12. Checked inducer motor amp draw.
13. Measured temperature differential from supply to return. 20 degrees measured.
14. Inspected drain lines and treated to prevent blockages 
15. Replaced return filter

Noticed surge protection on outdoor unit, but not indoor unit. Recommended surge protection to protect entirety of system from surges in power. 

Unit in good working order upon departure
Brayden W.
Brayden W.
Came out today for QC visit on new install. Started inside at t-stat (Honeywell) turned system on heat to verify function and then cooling. System is level all wiring is good no error codes. Measured 20 degree temp split from supply to return. Drain line is draining well at this time. System is clean annd operating as designed. Electric heat strips are functioning well. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Unit in good working order upon departure. Shut off unit upon departure per customer request.
Anna, TX 75409
Anna, TX - Came out today for QC visit on new install. Started inside at t-stat (Honeywell) turned system on heat to verify function and then cooling. System is level all wiring is good no error codes. Measured 20 degree temp split from supply to return. Drain line is draining well at this time. System is clean annd operating as designed. Electric heat strips are functioning well. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Unit in good working order upon departure. Shut off unit upon departure per customer request.
Anna, TX - Came out today for QC visit on new install. Started inside at t-stat (Honeywell) turned system on heat to verify function and then cooling. System is level all wiring is good no error codes. Measured 20 degree temp split from supply to return. Drain line is draining well at this time. System is clean annd operating as designed. Electric heat strips are functioning well. Outside unit is level all electrical components are good and tight. All components are operating as designed. Pressures were within manufacturer specifications. Unit in good working order upon departure. Shut off unit upon departure per customer request.
Shelby S.
Shelby S.
Preformed a heating maintenance on a carrier heat pump 2020. We tested all electrical components inside the unit along with all the safeties. We also checked for cleanliness throughout the unit. The electrical components and safeties tested within manufacturer specifications range. The temperature being supplied to the home was at 125 degrees with 79 being returned to the unit. We did find that the duct work and plenum boxes had a substantial amount of dust build up. We also noticed the blower wheel and wiring had formed a substantial amount of dust/debris/growth on them. With these findings we are providing estimates to have duct cleaning done along with a blower wheel cleaning. We then proceeded outside to test all electrical components on the outside unit. We tested run and start amps for the fan and compressor motors. The start amps were on the higher side at 53amps with the manufacturer range being at 72max amps on start up. We also found that he capacitor is testing out side of r
Anna, TX 75409
Anna, TX - Preformed a heating maintenance on a carrier heat pump 2020. We tested all electrical components inside the unit along with all the safeties. We also checked for cleanliness throughout the unit. The electrical components and safeties tested within manufacturer specifications range. The temperature being supplied to the home was at 125 degrees with 79 being returned to the unit. We did find that the duct work and plenum boxes had a substantial amount of dust build up. We also noticed the blower wheel and wiring had formed a substantial amount of dust/debris/growth on them. With these findings we are providing estimates to have duct cleaning done along with a blower wheel cleaning. We then proceeded outside to test all electrical components on the outside unit. We tested run and start amps for the fan and compressor motors. The start amps were on the higher side at 53amps with the manufacturer range being at 72max amps on start up. We also found that he capacitor is testing out side of r
Anna, TX - Preformed a heating maintenance on a carrier heat pump 2020. We tested all electrical components inside the unit along with all the safeties. We also checked for cleanliness throughout the unit. The electrical components and safeties tested within manufacturer specifications range. The temperature being supplied to the home was at 125 degrees with 79 being returned to the unit. We did find that the duct work and plenum boxes had a substantial amount of dust build up. We also noticed the blower wheel and wiring had formed a substantial amount of dust/debris/growth on them. With these findings we are providing estimates to have duct cleaning done along with a blower wheel cleaning. We then proceeded outside to test all electrical components on the outside unit. We tested run and start amps for the fan and compressor motors. The start amps were on the higher side at 53amps with the manufacturer range being at 72max amps on start up. We also found that he capacitor is testing out side of r

Your High Efficiency

Experts