Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX between September 2025 and October 2025.
The most recent job was on October 1, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
Upon arrival client Ben stated that his indoor fan was running but I was blowing warm air. He also stated the outside units fan was running as well. I proceeded to the thermostat and provided a call for cooling. I then went outside to check to see if the compressor was running. I hooked up my gauges to check pressures. I was getting 248psig on the high and low side, which was telling me that the refrigerant levels are okay but the compressor was not currently running. I proceeded to test the electrical components inside the unit and found that the capacitor was testing good on the fan side but the compressor side was testing low 28/45 microfarads. I also tested the Contactor and it was testing at 20.5 ohms which was testing on the high side. Start amps were testing within range but not as low as they should be testing. I presented all trouble areas to Ben and he elected to have the compressor saver bundle installed to help his unit run more efficiently. Temperature across the indoor co
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters
Preformed duct cleaning estimate for clients. Upon my inspection of the ducts I found that some of the supply vents had some dust debris on the outside and on the ceiling. I inspected the return plenum and blower wheel for dust/debris. I found both to have a good amount of dust build up. Clients stated they would like estimates sent over.
Preformed heating maintenance on a gas systems. I tested all safeties and electrical components inside of the furnace. All tested within manufacturer specifications. The blower wheel had dust build up on it. Filter did not need to be changed at this time. Gas lines were in good condition with no leaks. I presented findings of the blower wheel with dust build up. Client is interested in a possible duct cleaning in the future as well as a dryer vent cleaning. Unit is back in cooling mode and running upon departure. REMOVE AND CLEAN BLOWER ASSEMBLY LEVEL 1 A BLOWER ASSEMBLY MOVES AIR THROUGH YOUR SYSTEM. IF DIRTY, THE ASSEMBLY BLOWS THAT DIRT INTO YOUR SYSTEM. THIS CAN LEAD TO HIGHER ENERGY COSTS, ODORS AND DAMAGE TO THE UNIT.
I performed a single system heating maintenance on a 2025 gas system. I checked amps, filters, drains, electrical, cleanliness, and safeties. The home has whole home surge protection. The air advice reported showed high particles and VOCs. The carbon dioxide was high but the system recently had a fresh air installed. I offered to install an air scrubber to address these particles and chemical levels.
Arrived on site, found drain line clogged where it is attached to the coil drain pan. Also noticed extremely dirty evaporator coil. Tested capacitor and contactor on the outdoor unit. Contactor was testing within manufacture specifications, and was showing very little pitting. Capacitor was testing outside of range on the compressor side. I recommended replacing the capacitor to avoid a system failure. I also recommended a coil cleaning to improve the efficiency of the system, as well as, keep the drain line clear. Homeowner moved forward with coil cleaning, capacitor, replacement, and maintenance. I was able to unplug the drain line as a courtesy as I was already going to be in the coil for the cleaning. All work completed and tested system. 20° split measured unit in good working order upon departure.
Arrived on site for heating maintenance and charge check after washing unit. Rinsed condenser coil to promote heat exchange and prolong life of system. Measured refrigerant pressures after rinsing the coil and found them to be low. However, it is pretty cool and wet out today and the indoor temperature was 68 when I arrived. Therefore, I would not be able to accurately charge the unit. Informed customer I could add a couple pounds of refrigerant to get it closer to where it needs to be and then we check it further later on. Homeowner opted to leave it be for now. Checked contactor and found high ohms with burn marks on the contacts. Inform customer that this part was likely to fail soon. Homeowner opted leave it be for now. Capacitor was testing right on the edge of manufacturer specs. Tested unit and heating mode and found one leg of emergency heat unwired. Testing resistance on that leg of heat and I found no issues. I wired that leg of heat back and it started smoking, so I quickly
I performed a single system check on a 2019 gas system. This house has 2 system. The primary concern was that the drain line is backing up and flowing outside. I traced where the drain goes and found that the sink is clogged. The p trap is seeping water. I proposed undoing and clearing the p trap but fear that it needs a new trap. I examined the rest of the unit. I offered surge protection, clearing the drain, a capacitor, maintenance agreement, and combing the condenser fins.
Came out for 2 system maintenance Upon arrival started at tstats by turning on gas systems. Went into attic and started by checking the sequence of operation on the heating elements. Checked all heating components to verify proper operation. All compare operating as designed. Both filters (20x20x4) are dirty and need to be changed. I changed the filters for both units. I noticed both units could benefit from a blower wheel cleaning. Also both units could benefit by adding surge protection on systems to protect against power outages. Also to improve the air quality throughout the home i provided estimates to have 2 ozone free air scrubbers installed along with 2 uv sticks. Thank you for your time.
Upon arrival, I found that the system was not running. Customer stated he heard humming noise outside. The humming noise is from the reversing valve solenoid. The reason why it would come on is because the tab for the R and Rc was not in the 1 wire position. I switch it and checked the programming. The system is fully operational and cooling properly. I presented options for the solenoid and a hard start kit. The unit is rated for 109 on start up and is pulling 105.

