Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in September 2025.
The most recent job was on September 12, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
I preformed a single system maintenance on a 2022 Lennox gas system. System has 2 zones. I started by testing all electrical components inside on the air handler. All electrical tested within manufacturer specifications range. Temperature being supplied from the unit was at 47 degrees and returning at 67. I treated drain line with total c and changed the filter. I proceeded outside to check electrical components inside on the outdoor unit, I tested run and start amps of the compressor motor. All electrical components tested within manufacturer specifications. The unit was start on the high side of the amperage for the compressor motor. I rinsed the outdoor unit. I also provided an estimate to have a hard start kit installed to help assist the compressor motor on start up. Unit was cooling upon departure.
Upon arrival, I found that the system was operating properly. I checked my electrical components in the outdoor unit, temperature split, and refrigerant levels. I found no major issues. I attempted to simulate a warmer day by covering the top of the outdoor unit. I referenced the charge chart and it appears the system is slightly low. I had a 20 degree temperature drop. The system is showing about a 3 degree difference in what the sub cooling should be. I spoke with the home owner about my finding and the maintenance program. He did not want to perform any work at the time of service.
Upon arrival client stated that inside u it would come on but not blow cold air. I proceeded outside with the client to check electrical components and refrigerant pressure. I noticed the outdoor fan running but the compressor was not. Upon further inspection of the unit I found that the 70/7.5 capacitor to be bloated. And read at 0 microfarads. The fan was on a separate 5MFD capacitor and was reading at 4.8/5. I also tested the Contactor and was only getting 10 ohms, which is also a concern and could cause the unit not to work properly. I presented the client with my findings and he has elected to wait on repairs at this time. I explained to the customer that without the capacitor that his unit would stay in the same state that it was in. Standing refrigerant pressures were at 220psig on high and low side indicating that there is no leak in the system. Client elected to turn the outdoor disconnect back on. Unit is down and not cooling upon departure.
Both systems: 2007 gas systems Upon arrival, I found the outdoor fan motor not operating. I checked to see if it was locked up. I proceeded to test the capacitor. The capacitor was reading 0.8/5. I replaced the capacitor and began testing the system. The system is back to cooling. After testing the system, I found that the blower motor is leaking oil and likely will need replacement soon. The blower capacitor is reading 3.9/5. I presented these concerns to the customer and made him aware. The customer did not want pricing on other areas of concern at this time.
I performed a single system cooling maintenance on gas zoned system. Furnace is a 2017 and the condenser is 2018. I checked amps, capacitors, filter, drains, electrical, and cleanliness. The system is cooling inside of manufacture specifications. However I did notice some potential red flags for issues to come. 1. The primary drain is actively clogged. 2. The zone board is having an issue on zone 1. It can likely be addressed by switching to zone 3. This is causing the downstairs zone damper to become over heated. 3. The contactor’s contacts are heavily charred and could result in failure. 4. The blower has dust build up on the blower wheel. This leads to the blower straining to perform. 5. The compressor is starting just over the LRA. This causes damage to the compressor and other electrical components in the outdoor unit. 6. The capacitor is right at the bottom side of the manufacture recommended range. It is advised to replace before failure happens. Customer decline
Upon arrival I spoke with Jennifer. She stated they noticed the unit wasn’t working properly and the unit was blowing warm air. They stated the outdoor condenser was not coming on. I proceeded outside and checked all electrical components. Capacitor tested within manufacturer specifications. When I tested the Contactor I was getting 11 ohms and 0 volts coming out of the Contactor. Which shows signs of a bad Contactor. I presented the issue to Jennifer. She elected to replace the Contactor under 10 parts warranty. I installed the new Contactor and restored power to the unit. The unit is cooling properly. I tested pressures to insure of no refrigerant loss. Pressure were within manufacturer specifications. Temperature being supplied to the home was 55 coming out. Unit was cooling upon departure.
Returned to gather additional information. The heat kit is 10kw. The outdoor unit needs to be rotated 45 degrees counter clockwise to allow panel access. The ducts are newer flex ducts and not the old style. They are save to use the duct cleaning machine on. Filed out install sheet for when customer is ready to move forward.
Arrived to the property for the outdoor unit not coming on. The thermostat was off on arrival but I could hear the blower motor running. I turned the thermostat on and proceeded outside. I was not getting the proper voltage to the outdoor equipment and proceeded inside to verify that the indoor control board was sending the proper signal. I found the indoor control board with two 3amp fuses still working and not blown. I measured voltage to the outdoor equipment and the primary board was not sending the correct signal. I diagnosed a failed primary control board most likely caused by the recent blackout that occurred over the weekend. I discussed adding surge protection to the equipment to help prevent this from potentially occurring again. The control board is in stock and we will pick it up and return to replace it today. We will also install two surge protectors one indoor and another outdoor. The landlord signed the estimate and gave us authorization to charge the card on file.
Arrived on site, homeowner had no issues to bring to my attention. Proceeded with cooling maintainance 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange Measured high start amps on outdoor compressor. This leads to excessive wear and tear on components as they are working harder to get moving. Recommend hard start kit in order to bring these start amps down and prolong sys
Before arriving, I reviewed the inspector’s concerns. I investigated these concerns and examined the system. The inspector was concerned about the cleanliness of the evaporator coil and an opening on the top portion of the supply plenum. After inspecting the cleanliness of the evaporator coil, I determined that there is no need for further cleaning. We have previously performed a no rinse cleaning and the work looks fine. I addressed the air leak on the top portion of the plenum. I sealed it using metal tape, spray glue, and mastic. System was tested and is cooling to manufacture specifications at the time of service.

