Adon Complete Air Conditioning and Heating is Anna’s local HVAC company. Most contractors serving this area are driving in from McKinney or further south. We’re not. Our office is right here in Anna. Our owner, Jesse Villarreal, has been serving Collin County homeowners for over 27 years, and our technicians run calls in Anna neighborhoods every single day. Whether you’re in an established neighborhood near downtown, a newer community like Liberty Hills, or getting ready to move into Sherley Farms, we know this city and we’re ready to help.
HVAC Services in Anna, TX
Anna is one of the fastest-growing cities in North Texas, and with thousands of new homes coming online, the demand for reliable heating and cooling service has never been higher. Here’s what we offer Anna homeowners:
AC Repair. Fast diagnosis and repair on all makes and models. We’re already in Anna every day, which means getting to you quickly isn’t a problem.
AC Installation. Whether you’re moving into a new build or replacing an aging system, we size every installation correctly using a proper load calculation. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Anna homeowners in new construction, getting on a maintenance plan early is one of the best ways to protect your warranty and catch issues before they become expensive.
Mini-Split Installation. Ductless systems work especially well for garages, home offices, bonus rooms, and additions, all of which are common in Anna’s newer construction neighborhoods.
Heat Pump Installation and Repair. Heat pumps provide year-round heating and cooling from one system. A popular option for Anna’s newer builds where energy efficiency matters.
Indoor Air Quality. New construction homes are built tight for energy efficiency, which means less fresh air circulation. Air filtration systems, UV purifiers, and ventilators help keep the air inside your home clean and healthy. We offer a free “What Are You Breathing?” screening to Anna homeowners.
Air Duct Cleaning. Construction dust and debris in ductwork is a real issue in new builds. Professional duct cleaning after move-in is something we recommend for most Anna homeowners in newer communities.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Anna and Collin County.
HVAC Services for Anna’s Growing Neighborhoods
Anna’s population grew roughly 177 percent between 2022 and 2023, making it one of the fastest-growing cities in the country. Sherley Farms, a $1.5 billion master-planned community, broke ground in March 2026 and will bring roughly 3,000 new homes to the city over the next several years. Liberty Hills is adding another 1,800 homes near US-75. That’s thousands of new HVAC systems coming online in a city that’s already one of our busiest service areas.
For homeowners in newer construction, the first few years matter most. Builder-installed systems need to be maintained on schedule to keep warranties valid, and new ductwork should be inspected and cleaned after construction is complete. We’ve helped Anna homeowners navigate all of this, and we know exactly what to look for.
Why Anna Homeowners Choose Adon Complete
- We live here. Our office is at 824 S Central Expressway in Anna. When you call us, you’re calling your neighbor, not a company routing calls from a regional office in Dallas.
- Jesse Villarreal has been doing this for over 27 years. He’s the owner and is actively involved in every aspect of the business. That level of accountability is hard to find at a larger company.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained installation and the full manufacturer’s warranty on every system we install.
- We service everything. Whatever brand is in your home, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access.
Frequently Asked Questions
Here are some answers to common questions we get about our Anna HVAC services.
How much does AC repair cost in Anna, TX?
Most AC repairs in Anna run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement are on the lower end. More involved repairs, like a blower motor or evaporator coil, will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Anna?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Anna and Collin County. Since we’re based in Anna, response times are typically faster here than anywhere else we serve.
What HVAC brands do you service in Anna?
We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise in those brands.
Do you offer HVAC maintenance plans in Anna?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. For new construction homeowners especially, staying on a maintenance schedule helps protect your builder warranty.
What areas near Anna do you serve?
We serve all of Anna and the surrounding Collin County communities, including McKinney, Sherman, Melissa, Van Alstyne, and Allen.
Schedule HVAC Service in Anna Today
We’re already in your neighborhood. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Anna, TX
Anna, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Anna, TX in August 2025.
The most recent job was on August 4, 2025.
Adon Complete Air Conditioning and Heating has completed 589 jobs in Anna, TX in the last 12 months. The first job there was in February 2020.
Job Locations
I arrived at our clients home for a second opinion regarding his heat pump unit. I proceeded first outside and verified that the unit compressor was short to ground. This is a dead compressor and I could not offer any repairs. I proceeded into the attic unit and analyzed the existing equipment and potential modifications that would be needed to ensure the new equipment ran optimally. We discussed relocating the unit to a more open part of the attic and hanging the corresponding ductwork off of the attic floor. This would allow for future attic insulation work as well as optimal airflow throughout the home. We discussed the 14 and 15 SEER options and I added the modifications option to both estimates. Our client wanted some time to review his options and we will follow up tomorrow.
Arrived to clients home for concerns it was not cooling properly. The system was off on arrival. I asked our client to turn the unit on and proceeded to test and inspect the electrical components. Everything turned on and was running properly. I tested the capacitor and it was still in range but near failure. The run amps to the compressor were also in range. I proceeded inside and confirmed the unit was cooling properly. I changed the air filter for our client and we discussed possible issues such as intermittent failure of the thermostat or over heating of the compressor. She will continue to monitor the system performance. The unit is cooling on departure.
Complimentary comfort advisor visit to provide options for indoor comfort solutions.
System is a 2022 Trane heat pump. No zones or communication. Upon arrival, I found that the outdoor unit was not operating. I verified that I was getting the 24v outside and the contactor was pulled in. I checked my high voltage. I found that I was missing 1 leg of power to the unit. I traced it all the way back to the main breaker in the panel. The breaker is a 50 amp 2 pole GE breaker. I informed the customer that they will need an electrician to perform this repair. From what I could check, I determined that this system should operate when power returns. I informed the customer of the 30 day recall time frame with the collection of the 45.00 dispatch.
Upon arrival, I found the system fully operational. I referred to past calls. I reached out to Jacob and since this has been an ongoing going issue, I replaced it under parts and labor warranty. This issues dates back to before the labor warranty expired. The thermostat had a feint shorted electrical smell once I removed it.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Found condenser coil to be extremely dirty causing pressures to look a bit off. However after cleaning measured a perfect 55 degrees supply temp. Unit in good working order upon departure.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Measured high start amps. This will produce increased wear on the components of the unit. Recommended hard start kit to reduce start amps and reduce wear and tear occurring on the unit. Unit in good working order upon departure
I examined the cleanliness of the indoor system and ductwork. The inside of the system isn’t too bad. The ducts has some build up, and they could use some sprucing up. I recommend adding a u/v light to help maintain the ducts after cleaning occurs. I presented options for all levels and allowed the customer to examine all that we offer.
Upon arrival, I found that the outdoor unit was not coming on in a call for cool. I verified that I had high voltage and removed the panel. I found the 70/5 capacitor was bloated. This an indication of failure. I check the reading and had 7/70 on the compressor. I presented options and the customer elected to install a Turbo200x capacitor without membership. I proceeded to test after the repair. The system is cooling with a 19 temperature split. The unit is a 2019 carrier Heatpump that services 2 floors without a zone set up. I told the customer that it is addressable, but would be more ethical and logical to address it once the system needs replacement. 5 year part warranty on Turbo200x
Arrived on site and found condenser fan running without the compressor. Measured capacitance on capacitor 300Nf. Well outside of manufacturer specifications 45/5 cap. Also tested resistance on contactor 21.9ohms with signs of burning and pitting on the contacts. Also outside of manufacturer specifications. The capacitor has failed and the contactor is not far behind. The condenser coil was extremely plugged and dirty. This will drastically reduce the amount of airflow the coil receives; putting a lot of stress on the unit. Upon reviewing the blower motor it was found that the blower wheel was extremely dirty and had been replaced before. It is likely due to the amount of dust on the blower wheel that the old motor burned out. Homeowner elected to replace capacitor and contactor with VIP maintenance. Performed contactor and capacitor replacement. Unit started up without issue. Took refrigerant pressures and found them to be a bit off. Measured temperature split from supply to return and

