Frisco has grown faster than almost any city in America over the past two decades, and the homes here reflect it. Larger floor plans, multi-zone systems, high-efficiency equipment, and newer construction in neighborhoods like The Fields, Phillips Creek Ranch, and Viridian. Keeping all of it running well takes an HVAC company that knows what it’s doing. Adon Complete Air Conditioning and Heating has been running calls for HVAC service in Frisco for years from our home base in Anna, just up the Dallas North Tollway corridor. We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer, and we’re available 24 hours a day, 7 days a week for emergencies.
What We Do for Frisco Homeowners
AC Repair. We diagnose and repair all makes and models. Frisco’s newer construction often means multi-zone systems and communicating equipment — our technicians know how to work on all of it.
AC Installation. When it’s time to replace, we size every system correctly using a proper load calculation. That matters especially in Frisco’s larger homes where an improperly sized system will short-cycle and leave rooms uncomfortable. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Frisco homeowners with high-end systems, staying on a maintenance schedule is one of the best ways to protect your investment.
Mini-Split Installation. Garages, home offices, casitas, and bonus spaces are common in Frisco’s larger homes. Mini-splits handle these spaces cleanly without touching your central system.
Heat Pump Installation and Repair. Heat pumps provide both heating and cooling from one system and work well in North Texas’s climate. A practical choice for Frisco homeowners upgrading to a more efficient setup.
Indoor Air Quality. Air filtration systems, UV purifiers, humidifiers, dehumidifiers, and a free “What Are You Breathing?” screening. Frisco’s tight construction means less natural ventilation, making air quality systems more important than in older homes.
Air Duct Cleaning. Even newer ductwork accumulates contaminants over time. Professional duct cleaning improves air quality and keeps your system running efficiently throughout the home.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. In a larger Frisco home, that adds up fast. We inspect, repair, and seal ductwork throughout the area.
Why Frisco Homeowners Choose Adon Complete
Frisco has no shortage of HVAC companies competing for business. Here’s why our customers keep calling us back.
We know multi-zone and communicating systems. The job notes from our Frisco calls show what we actually work on here – damper adjustments, multi-system diagnostics, communicating Trane equipment, humidity management in two-story homes. This isn’t routine work, and we handle it well.
Jesse Villarreal has over 27 years of experience. He’s the owner and is directly involved in how the business operates. When something goes wrong, you’re dealing with a company where the owner’s reputation is on the line.
We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained on the brands most common in Frisco’s newer construction. Full manufacturer warranty on every system we install.
The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access. Straightforward and affordable.
Serving Frisco and Surrounding Collin County Communities
We serve all of Frisco, including The Fields, Phillips Creek Ranch, Viridian, Stonebriar, and the established neighborhoods along Preston Road and the Dallas North Tollway. We also serve the surrounding communities of Allen, McKinney, Anna, Melissa, and Sherman.
Frequently Asked Questions
Here are some common questions we get about our HVAC services in Frisco.
How much does AC repair cost in Frisco, TX?
Most AC repairs in Frisco run between $150 and $600 depending on the type of repair. Frisco’s newer homes often have multi-zone systems and higher-end equipment, which can affect parts costs. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you service multi-zone systems in Frisco?
Yes. Multi-zone systems and communicating HVAC equipment are common in Frisco’s larger homes, and our technicians work on them regularly. We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, and more.
Do you offer HVAC maintenance plans in Frisco?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. Preventive maintenance is especially important for the multi-system setups common in Frisco’s larger homes.
Do you offer emergency HVAC service in Frisco?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Frisco. When you call after hours, you reach a real person who can get a technician to your home fast.
What areas near Frisco do you serve?
We serve all of Frisco and the surrounding communities including Allen, McKinney, Anna, Melissa, and Sherman.
Ready to Get Your System Serviced?
Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online for HVAC services in Frisco. We handle everything from routine maintenance to emergency repairs throughout Frisco and Collin County.
Recent Jobs and Reviews in Frisco, TX
Frisco, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Frisco, TX between April 2026 and May 2026.
The most recent job was on May 26, 2026.
Adon Complete Air Conditioning and Heating has completed 51 jobs in Frisco, TX in the last 12 months. The first job there was in March 2020.
Job Locations
Rinsed off all 4 units with water.
Arrived on site found thermostat with no display. Tested voltage to thermostat and found 24V. This confirms the thermostat is no longer functioning and must be replaced. Performed thermostat installation and programming. Tested functionality and found all to be working well 57 degree supply 80 return. No further issues at this time system running upon departure.
I performed a single cooling maintenance on a 2010 gas system. This system services the upstairs. During my thorough evaluation, I determined that this system is mechanically performing well. I discovered 2 concerns. The thermostat has corrosion present from batteries, and the outdoor unit needs a chemical cleaning. The system currently does not have a water safety switch. With this system’s age, the customer and I agreed that it is important to protect this system. I offered to install surge protection to protect it as much as possible.
Completed 4 system maintenance on 3 2006 rheem gas units and 1 2017 Lennox gas unit. I tested all electrical on the inside of each unit. All tested within manufacturer specifications. I treated and tested each drain line with total c and water, I changed the filter for the clients at today’s visit, 20x25x4. I did notice a substantial amount of dust build up in each return duct and plenum boxes on each unit as well as the blower wheels. I proceeded outside where I tested all electrical components on the outside units all tested within manufacturer specifications except for the upstairs units capacitor and Contactor. The capacitor failed at .04/60 mfd and the Contactor is rusted and pitted. If these units completely fail this unit will no longer run unit parts are replaced. Also there is a substantial amount of dust build up on each units condenser coils. Units were cooling upon departure. Capacitor has failed at .04/60 Contactor has pitting and rust forming
I performed a 2 system cooling maintenance on 2005 gas equipment. The refrigerant type is R22. During my thorough evaluation, I discovered various issues. The downstairs system needs a 1/2 hp blower motor due to it leaking oil, the blower capacitor that powers the motor, a deep cleaning of the indoor and outdoor units, a replacement emergency drain pan, and the outdoor electrical needs to be rebuilt. The upstairs system needs a deep cleaning of the indoor and outdoor equipment, a blower capacitor that powers the motor, a replacement emergency drain pan, and a capacitor that powers the compressor. The upstairs does have a refrigerant leak causing poor cooling. I provided options during my visit to address these issues. These options are broken down from needs immediate action to important but less severe. Customer opted to have our comfort consultant to come out and go over replacement options today 5/12 between 3pm-5pm.
Upon arrival, I found the system cooling mostly as intended. I thoroughly evaluated the 2012 gas system. The customer informed me that when the system was frozen the blower motor was hardly performing. Likely the ECM control module is intermittently failing. I checked refrigerant pressures. I observed that the pressures are slightly low indicating a leak is present. The location of the potential leak is unknown currently. According to the gauges and appearance of the outdoor unit, I am advising the outdoor unit be deep cleaned. I went over the options and solutions for these issues that were noticed. Customer scheduled to have the comfort advisor to come by and go over replacement options for the downstairs unit. The visit is scheduled for after 5pm on Monday 5/11.
I performed a 4 system cooling maintenance on gas equipment. Three of the systems are from 2016 and one is from 2014. I checked amps, drains, capacitors, filters, electrical, cleanliness, and safeties. During my thorough evaluation, I determined that these systems are currently performing well. I advised adding surge protection to indoor equipment to minimize damage in the case of poor power supply/surges. Customer declined during the visit. I installed 4 filter upgrade kits and gave the customer the filter information. The units are cooling upon departure.
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Found mitigation test mode error on thermostat history around February. Adjusted discharge air temp sensor t
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. 15. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. Found capacitors on both outdoor units testing outside of manufacturer specifications and liable to fail at
I investigated the customer’s concerns about the airflow to the bedroom. The duct run is long and placed at the front of the plenum. There are not dampers in the system. This is causing the air to bypass the duct. Customer wants to relocate the supply vent that is above the shower to above the door. To address the humidity of the bathroom, I suggested running the humidity fan for approximately 20 to 30 mins after a shower with the bathroom door shut. Additionally, upgrading the thermostats to one that offers dehumidification. Customer brought up wanting options for water safety switches. I provided options to the customer during the visit. He asked for me to email the options.

