Frisco has grown faster than almost any city in America over the past two decades, and the homes here reflect it. Larger floor plans, multi-zone systems, high-efficiency equipment, and newer construction in neighborhoods like The Fields, Phillips Creek Ranch, and Viridian. Keeping all of it running well takes an HVAC company that knows what it’s doing. Adon Complete Air Conditioning and Heating has been running calls for HVAC service in Frisco for years from our home base in Anna, just up the Dallas North Tollway corridor. We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer, and we’re available 24 hours a day, 7 days a week for emergencies.
What We Do for Frisco Homeowners
AC Repair. We diagnose and repair all makes and models. Frisco’s newer construction often means multi-zone systems and communicating equipment — our technicians know how to work on all of it.
AC Installation. When it’s time to replace, we size every system correctly using a proper load calculation. That matters especially in Frisco’s larger homes where an improperly sized system will short-cycle and leave rooms uncomfortable. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Frisco homeowners with high-end systems, staying on a maintenance schedule is one of the best ways to protect your investment.
Mini-Split Installation. Garages, home offices, casitas, and bonus spaces are common in Frisco’s larger homes. Mini-splits handle these spaces cleanly without touching your central system.
Heat Pump Installation and Repair. Heat pumps provide both heating and cooling from one system and work well in North Texas’s climate. A practical choice for Frisco homeowners upgrading to a more efficient setup.
Indoor Air Quality. Air filtration systems, UV purifiers, humidifiers, dehumidifiers, and a free “What Are You Breathing?” screening. Frisco’s tight construction means less natural ventilation, making air quality systems more important than in older homes.
Air Duct Cleaning. Even newer ductwork accumulates contaminants over time. Professional duct cleaning improves air quality and keeps your system running efficiently throughout the home.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. In a larger Frisco home, that adds up fast. We inspect, repair, and seal ductwork throughout the area.
Why Frisco Homeowners Choose Adon Complete
Frisco has no shortage of HVAC companies competing for business. Here’s why our customers keep calling us back.
We know multi-zone and communicating systems. The job notes from our Frisco calls show what we actually work on here – damper adjustments, multi-system diagnostics, communicating Trane equipment, humidity management in two-story homes. This isn’t routine work, and we handle it well.
Jesse Villarreal has over 27 years of experience. He’s the owner and is directly involved in how the business operates. When something goes wrong, you’re dealing with a company where the owner’s reputation is on the line.
We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained on the brands most common in Frisco’s newer construction. Full manufacturer warranty on every system we install.
The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access. Straightforward and affordable.
Serving Frisco and Surrounding Collin County Communities
We serve all of Frisco, including The Fields, Phillips Creek Ranch, Viridian, Stonebriar, and the established neighborhoods along Preston Road and the Dallas North Tollway. We also serve the surrounding communities of Allen, McKinney, Anna, Melissa, and Sherman.
Frequently Asked Questions
Here are some common questions we get about our HVAC services in Frisco.
How much does AC repair cost in Frisco, TX?
Most AC repairs in Frisco run between $150 and $600 depending on the type of repair. Frisco’s newer homes often have multi-zone systems and higher-end equipment, which can affect parts costs. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you service multi-zone systems in Frisco?
Yes. Multi-zone systems and communicating HVAC equipment are common in Frisco’s larger homes, and our technicians work on them regularly. We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, and more.
Do you offer HVAC maintenance plans in Frisco?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. Preventive maintenance is especially important for the multi-system setups common in Frisco’s larger homes.
Do you offer emergency HVAC service in Frisco?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Frisco. When you call after hours, you reach a real person who can get a technician to your home fast.
What areas near Frisco do you serve?
We serve all of Frisco and the surrounding communities including Allen, McKinney, Anna, Melissa, and Sherman.
Ready to Get Your System Serviced?
Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online for HVAC services in Frisco. We handle everything from routine maintenance to emergency repairs throughout Frisco and Collin County.
Recent Jobs and Reviews in Frisco, TX
Frisco, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Frisco, TX between March 2026 and April 2026.
The most recent job was on April 6, 2026.
Adon Complete Air Conditioning and Heating has completed 51 jobs in Frisco, TX in the last 12 months. The first job there was in March 2020.
Job Locations
Indoor Blower and Evaporator Coil Inspection – Upstairs & Downstairs Systems During our inspection, we found that both the upstairs and downstairs indoor blowers and evaporator coils are extremely dirty and in need of a thorough cleaning and sanitization. Blower Cleaning: The indoor blower assemblies are heavily coated with accumulated dirt, dust, and debris. To properly restore airflow and maintain system efficiency, the blower will need to be completely removed from the system. The entire blower cage will be professionally cleaned to eliminate all contaminants. This step is critical because a dirty blower reduces airflow, forces the system to work harder, and can significantly shorten the life of the motor. Evaporator Coil Cleaning and Sanitization: The evaporator (Raptor) coils in both systems are heavily contaminated and must be washed and sanitized. Dirty coils restrict airflow, reduce heat exchange efficiency, and can lead to higher energy consumption and uneven heating or coo
1. Visually inspected condenser coil for leaks and abnormalities. 2. Inspected condenser fan motor, blades and bearings. 3. Inspected, cleaned, and, tightened wiring connections. 4. Measured capacitance of compressor/fan motor capacitor. 5. Inspected and measured resistance of contactor 6. Measured compressor current draw. 7. Measured condenser fan motor amp draw. 8. Inspected and replaced return filter. 9. Inspected return plenum for dust or debris. 10. Inspected evaporator coil for cleanliness and oxidation. 11. Inspected blower motor/ blower wheel for dust and debris 12. Measured blower motor current draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Tested drain lines for proper drainage and treated to prevent blockages. Both units outdoor coils are extremely dirty and plugged with dirt and debris. This will prevent airflow from passing through the coils and will cause a huge amount of stress on compressor, connected electrical components
Upon my completion of my thorough evaluation of the downstairs you. I was able to confirm that there is an intermittent issue with the blower going in and out. I did speak with the client about them issue and she is fully aware of what is happening. Client would like to hold off on the repair for now and see what happens. I did let her know it could fail when I leave here today or it could fail way into the future. Unit is currently cooling upon departure.
Cooling maintenance on 1. Rinsed condenser with water to promote heat exchange and reduce stress on system by removing dust and debris. 2. Visually inspected condenser coil for leaks and abnormalities. 3. Inspected condenser fan motor, blades and bearings. 4. Inspected, cleaned, and, tightened wiring connections. 5. Measured capacitance of compressor/fan motor capacitor. 6. Inspected and measured resistance of contactor 7. Measured compressor current draw. 8. Measured condenser fan motor amp draw. 9. Inspected and replaced return filter. 10. Inspected return plenum for dust or debris. 11. Inspected evaporator coil for cleanliness and oxidation. 12. Inspected blower motor/ blower wheel for dust and debris 13. Measured blower motor current draw. 14. Measured temperature differential from supply to return. 20 degrees measured. 15. Tested drain lines for proper drainage and treated to prevent blockages. Found blower motor on downstairs unit failed causing unit to freeze up due to no ai
Upon completion of my thorough evaluation. I found that the evaporator and condenser coil could use a good deep cleaning. By cleaning both coils it can help maintain the performance and efficiency of the unit and help increase the life as well. I also found that the capacitor is the original capacitor from install and could benefit from being upgraded. Also the unit is over amping at 100 amps max amperage is at 124 amps. By installing a hard start kit, it can help the units compressor last longer by bringing those high amp down. By adding surge protection it can help protect the unit from lightning strikes and other types of power surges.
Thank you for allowing us the opportunity to evaluate the ductless wall-mounted system at your commercial property. After thoroughly testing the condensate drainage system, we identified that the existing drain line is leaking approximately halfway through the run above the office ceiling area. During our evaluation, we: • Tested the condensate pump by pouring water directly into the pump reservoir. • Introduced several gallons of water to confirm proper drainage. • Applied nitrogen pressure through the copper drain line to attempt clearing any blockage. • Performed a vacuum suction process to remove possible debris buildup. Despite these efforts, the drain line continues to leak and does not drain properly, indicating deterioration, improper pitch, internal blockage, or physical damage within the ceiling cavity. Based on our findings, we recommend installing a new dedicated condensate drain line (home run) from the indoor ductless wall-mounted unit directly to the janitorial m
1. Rinsed condenser with water to promote heat exchange and reduce stress on system 2. Visually inspected condenser coil for debris/ dirty. 3. Inspected condenser fan motor. 4. Inspected condenser fan blades. 5. Inspected/ cleaned wiring connections. 6. Tested compressor/ condenser fan motor capacitor. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirty. 11. Inspected evaporator coil. 12. Inspected blower motor/ blower wheel. 13. Checked blower amp draw. 14. Measured temperature differential from supply to return. 20 degrees measured. 15. Inspected drain lines and treated to prevent blockages Upon initial inspection found downstairs condenser coil looking very dirty. After rinsing with water I found a decent amount of corrosion on coils. This will cause additional stress on unit as it cannot exchange heat as efficiently. Tested capacitor and contactor for downstairs unit and foun
Upon arrival, I discovered the outdoor not coming on. I gauged up and found the system completely empty of R22. I spoke with the client about my findings and they approved having our comfort specialist coming out on 3/7/2026 between 10am-12pm.
1. Rinsed condenser with water to promote heat exchange and reduce stress on system 2. Visually inspected condenser coil for debris/ dirty. 3. Inspected condenser fan motor. 4. Inspected condenser fan blades. 5. Inspected/ cleaned wiring connections. 6. Tested compressor/ condenser fan motor capacitor. 7. Checked compressor amp draw. 8. Checked condenser fan motor amp draw. 9. Inspected / replaced return filter. 10. Inspected return plenum for debris/ dirty. 11. Inspected evaporator coil. 12. Inspected blower motor/ blower wheel. 13. Checked blower amp draw. 14. Measured temperature differential from supply to return. 20 degrees measured. 15. Inspected drain lines and treated to prevent blockages Found supply temp measuring 64. Found refrigerant pressures to be low and checked previous work for leaks and found none. Found minor leakage around shrader valves. Tightened valve and added a touch of refrigerant to ensure system was working properly and found no further issues at this time.
Thank you for allowing us the opportunity to evaluate the ductless wall-mounted system at your commercial property. After thoroughly testing the condensate drainage system, we identified that the existing drain line is leaking approximately halfway through the run above the office ceiling area. During our evaluation, we: • Tested the condensate pump by pouring water directly into the pump reservoir. • Introduced several gallons of water to confirm proper drainage. • Applied nitrogen pressure through the copper drain line to attempt clearing any blockage. • Performed a vacuum suction process to remove possible debris buildup. Despite these efforts, the drain line continues to leak and does not drain properly, indicating deterioration, improper pitch, internal blockage, or physical damage within the ceiling cavity. Based on our findings, we recommend installing a new dedicated condensate drain line (home run) from the indoor ductless wall-mounted unit directly to the janitorial m

