Frisco has grown faster than almost any city in America over the past two decades, and the homes here reflect it. Larger floor plans, multi-zone systems, high-efficiency equipment, and newer construction in neighborhoods like The Fields, Phillips Creek Ranch, and Viridian. Keeping all of it running well takes an HVAC company that knows what it’s doing. Adon Complete Air Conditioning and Heating has been running calls for HVAC service in Frisco for years from our home base in Anna, just up the Dallas North Tollway corridor. We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer, and we’re available 24 hours a day, 7 days a week for emergencies.
What We Do for Frisco Homeowners
AC Repair. We diagnose and repair all makes and models. Frisco’s newer construction often means multi-zone systems and communicating equipment — our technicians know how to work on all of it.
AC Installation. When it’s time to replace, we size every system correctly using a proper load calculation. That matters especially in Frisco’s larger homes where an improperly sized system will short-cycle and leave rooms uncomfortable. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. For Frisco homeowners with high-end systems, staying on a maintenance schedule is one of the best ways to protect your investment.
Mini-Split Installation. Garages, home offices, casitas, and bonus spaces are common in Frisco’s larger homes. Mini-splits handle these spaces cleanly without touching your central system.
Heat Pump Installation and Repair. Heat pumps provide both heating and cooling from one system and work well in North Texas’s climate. A practical choice for Frisco homeowners upgrading to a more efficient setup.
Indoor Air Quality. Air filtration systems, UV purifiers, humidifiers, dehumidifiers, and a free “What Are You Breathing?” screening. Frisco’s tight construction means less natural ventilation, making air quality systems more important than in older homes.
Air Duct Cleaning. Even newer ductwork accumulates contaminants over time. Professional duct cleaning improves air quality and keeps your system running efficiently throughout the home.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. In a larger Frisco home, that adds up fast. We inspect, repair, and seal ductwork throughout the area.
Why Frisco Homeowners Choose Adon Complete
Frisco has no shortage of HVAC companies competing for business. Here’s why our customers keep calling us back.
We know multi-zone and communicating systems. The job notes from our Frisco calls show what we actually work on here – damper adjustments, multi-system diagnostics, communicating Trane equipment, humidity management in two-story homes. This isn’t routine work, and we handle it well.
Jesse Villarreal has over 27 years of experience. He’s the owner and is directly involved in how the business operates. When something goes wrong, you’re dealing with a company where the owner’s reputation is on the line.
We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. Factory-trained on the brands most common in Frisco’s newer construction. Full manufacturer warranty on every system we install.
The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access. Straightforward and affordable.
Serving Frisco and Surrounding Collin County Communities
We serve all of Frisco, including The Fields, Phillips Creek Ranch, Viridian, Stonebriar, and the established neighborhoods along Preston Road and the Dallas North Tollway. We also serve the surrounding communities of Allen, McKinney, Anna, Melissa, and Sherman.
Frequently Asked Questions
Here are some common questions we get about our HVAC services in Frisco.
How much does AC repair cost in Frisco, TX?
Most AC repairs in Frisco run between $150 and $600 depending on the type of repair. Frisco’s newer homes often have multi-zone systems and higher-end equipment, which can affect parts costs. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you service multi-zone systems in Frisco?
Yes. Multi-zone systems and communicating HVAC equipment are common in Frisco’s larger homes, and our technicians work on them regularly. We service all makes and models, including Trane, Lennox, Carrier, Daikin, Mitsubishi, and more.
Do you offer HVAC maintenance plans in Frisco?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. Preventive maintenance is especially important for the multi-system setups common in Frisco’s larger homes.
Do you offer emergency HVAC service in Frisco?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Frisco. When you call after hours, you reach a real person who can get a technician to your home fast.
What areas near Frisco do you serve?
We serve all of Frisco and the surrounding communities including Allen, McKinney, Anna, Melissa, and Sherman.
Ready to Get Your System Serviced?
Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online for HVAC services in Frisco. We handle everything from routine maintenance to emergency repairs throughout Frisco and Collin County.
Recent Jobs and Reviews in Frisco, TX
Frisco, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Frisco, TX between June 2025 and August 2025.
The most recent job was on August 15, 2025.
Adon Complete Air Conditioning and Heating has completed 51 jobs in Frisco, TX in the last 12 months. The first job there was in March 2020.
Job Locations
Returned today to replace upstairs capacitor. Once replaced I tested and measured the start and run amps for the compressor and outdoor fan motor. Both are still testing within manufacturer specifications. I also labeled the outdoor disconnect boxes for the homeowner for both up and downstairs units. We also discussed his existing maintenance plan and I presented the option to pay for the maintenance on a monthly basis versus all upfront. He preferred that method and elected to sign up for another year starting in January 2026. Both units are cooling on departure.
Warranty call for heat pump system not cooling properly. Upon arrival customer mentioned the drain adjustment we’ve done to get the system draining properly because the float switch kept activating. He said the last time we came out to do that repair the system ran good for a couple weeks but it started acting up again. He keeps his thermostat set to 76 during the day and 74 at night sometimes 72. Checking the alert history I noticed that around 6pm is when the float switch starts activating and goes on and off throughout the night. I also saw that the supply temperature sensor was active meaning the temperature within the system was below a set temperature that could harm the system. I checked the drain line and it’s not clogged but when I checked the blower speed it was set to 250cfm per ton, I went ahead and raised it to 350cfm per ton. With the way the speed was originally set the indoor coil was producing more condensation due to ice starting to form from lack of airflow but now
Preformed cooling maintenance on 2 systems. Tested all electrical components on the inside units. Both units tested within manufacturer specifications. Temp coming out was at 56&57 degrees supply. Changed filters for client. Treated both drain lines with total c. I proceeded outside to test both upstairs and downstairs units electrical components along with run and start amps of each unit. The upstairs unit all electrical components except for the Contactor tested within manufacturer specifications. The Contactor tested at 21.1 ohms. On the downstairs unit all electrical components tested within manufacturer specifications. The run amps for both the fan and compressor were testing within range. The start amps were exceeding the maximum range my meter could read which is over 100amps on start up. The start up amperage rating for the downstairs unit is 152.9 max. I provided estimates for both a hard start kit for the downstairs unit and a new Contactor for the upstairs unit. Client would
I performed a single system cooling maintenance. I checked amps, capacitor, filters, drains, electrical, and safeties. I noticed that the evaporator coil has some dust build up stuck in the fins. The micro channel condenser coil has oxidation present and some build up in the crevasses of the coil. I presented pricing for the cleanings. The customer would like to review the photos and decide at a later time.
Two system AC Maintenance. Homeowner said they had no issues other than high energy bills. Replaced both 20x25x1 filters. Applied total-c drain cleaner to primary drain. Neither system is retaining water and is draining properly. Both air distribution motor/wheels need to be pulled and cleaned. No float switches present. Water rinsed condenser coils. Checked all electrical components Found downstairs system condenser has pressure switch bypassed. Upstairs post coil wash delta temperature drop across the coil was 20 to 21°F Downstairs Post wash Delta temperature drop across the coil was only 14°F Priority Recommendations: - pull clean air distribution assemblies - float switches on both systems - air seal air leaks on upstairs evaporator coil - capacitor for outside equipment - hard start kits on both systems - surge protection on all components. - High voltage disconnect for outside downstairs equipment Recommend comfort advisor consultation for future replacement option. Est
I arrived to unit struggling to cool in the middle of the day. Client stated that unit ran fine but struggled to maintain temperature throughout the day. I went to the alert history and found the same alert had repeated throughout the course of the week. It was loosing communication to the thermostat and indoor unit is cooling at first I thought something to do with the Wi-Fi. I then found the code to correspond with the external water safety switch. I engaged the switch and confirmed it was intermittently shutting the unit off and not allowing the home to cool. The switch had some slope in line but I used plumbers strap to increase the slope and ensure it was draining properly. Mr Ferguson will monitor the system, it is cooling properly on departure.
I performed a tune up on 1 of the 2 systems. The systems are from 2020 and under a 10 year parts warranty. I checked the downstairs. The system has a u/v light in the evaporator coil, ss1 float switch, and ss3 float switch. I found that the unit does not have a good temperature drop. After further investigation, I found that the system is having a TXV issue with possible refrigerant contamination. The customer spoke about uncomfortable rooms and I checked for dampers. The system does not have dampers and the duct sizes could not be determined. The outdoor unit is starting with high amps and this leads to damage over time to the compressor. I provided options for a warranty TXV, dampers, and a hard start kit.
Male fitting, coupling, elbow, and p-trap. Fixed leak in drain line. Wrapped insulation of mini split to repair torn line set insulation. Repaired drywall damage from install. Checked refrigerant pressures to ensure it is no longer leaking.
Came out today for QC visit on new mini split install. Started inside turned system down to check over unit. System is level all wiring is good no error codes. Getting over 20 degree temp split on all heads. System is clean annd operating as designed. Outside unit is level all electrical components are good and tight. All components are operating as designed. Unit in good working order upon departure. Thank you for your time. ------------------ On downstairs split system I 1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential
Installation Includes: 1. Wall Mount Installation: • Secure mounting and installation of three wall-mounted indoor units in specified rooms. 2. Handheld Remote Controllers: • One handheld temperature control unit provided per zone (total of 3). 3. Refrigerant Line Sets: • Installation of copper refrigerant lines connecting each indoor unit to the outdoor condenser. 4. Control Wiring: • Installation of control wires between the outdoor unit and each indoor unit for system communication and function. 5. Condensate Drain Lines: • Each indoor unit will have a dedicated PVC condensate drain line routed to an appropriate drainage location. 6. System Start-Up and Commissioning: • Full system start-up, pressure testing, and refrigerant charging (if required) to manufacturer specifications. • System performance will be verified, and final refrigerant levels will be confirmed. Any necessary adjustments or refrigerant top-off will be included per Mitsubishi guidelines. ⸻ Additional

