Adon Complete Air Conditioning and Heating has been providing HVAC service in Sherman, TX, for years from our home base in Anna, just down Highway 75. Whether your AC goes out in July, your furnace won’t fire up in January, or you’re looking to upgrade to a more efficient system before the next season hits, our technicians are running calls in Sherman every week.
We service all makes and models, we’re a Trane Comfort Specialist and Mitsubishi-authorized dealer, and we’re available 24 hours a day, 7 days a week for emergencies. Whether you’re in Heritage Ranch, Canyon Creek, Westwood Village, or one of the established neighborhoods near the Grayson County Courthouse, we know this area and we’re ready to help.
HVAC Services We Offer in Sherman
We handle everything heating and cooling for Sherman homeowners and businesses. Here’s what we do:
AC Repair. Same-day service available throughout Sherman and Grayson County. We diagnose and repair all makes and models, and the majority of our calls are resolved in a single visit.
AC Installation. When it’s time for a new system, we size it correctly using a proper load calculation and install it in accordance with the manufacturer’s specifications. All new installations come with up to a 10-year labor warranty.
HVAC Maintenance. Our Adon Care Club plan is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, and 24/7 emergency access. It’s the smartest way to protect your system before the heat hits.
Mini-Split Installation. Ductless systems for rooms, additions, or whole-home comfort without ductwork. We install single- and multi-zone systems throughout Sherman and surrounding Grayson County communities.
Heat Pump Installation and Repair. Heat pumps provide both heating and cooling from a single system. This is a practical choice for Sherman homeowners who want year-round efficiency without separate units.
Indoor Air Quality. Air filtration systems, UV purifiers, humidifiers, dehumidifiers, and a free “What Are You Breathing?” screening for Sherman area homeowners.
Air Duct Cleaning. Professional duct cleaning removes allergens, dust, and debris from your system, improving air quality throughout your home.
Air Duct Repair and Sealing. Leaky ducts can cost you 20 to 30 percent of your system’s output. We inspect, repair, and seal ductwork throughout Sherman and Grayson County.
Why Sherman Homeowners Choose Adon Complete
- We’re close by. We’re based in Anna, TX, a short drive down Highway 75. Our technicians are in Sherman neighborhoods regularly and know the homes and properties on both sides of US-75.
- Owner Jesse Villarreal has over 27 years of HVAC experience. When you call Adon Complete, you’re not calling a franchise call center. You’re calling a local company where the owner is actively involved and his reputation is on the line with every job.
- We’re a Trane Comfort Specialist and Mitsubishi-authorized dealer. That means factory-trained installation and the full manufacturer warranty on every system we install. Not every HVAC contractor serving Sherman can say that.
- We service everything. Whatever brand you have, we can work on it. We don’t turn jobs away because the equipment isn’t ours.
- The Adon Care Club is $12 a month. Two tune-ups a year, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency access. It’s the most affordable way to keep your system reliable year-round.
AC and Heating Service Throughout Sherman and Grayson County
We service every neighborhood in Sherman including Heritage Ranch, Westwood Village, Canyon Creek, Parkhaven, O’Hanlon Ranch, and the established neighborhoods around downtown and the Grayson County Courthouse area. We also serve the surrounding Grayson County communities of Denison, Van Alstyne, Gunter, Howe, Tom Bean, Pottsboro, and Whitesboro.
Sherman HVAC FAQ
Here are some common questions we get.
How much does AC repair cost in Sherman, TX?
Most AC repairs in Sherman run between $150 and $600, depending on the type of repair. Simple fixes like a capacitor replacement or refrigerant recharge are on the lower end. More involved repairs like a blower motor or evaporator coil replacement will cost more. We provide a clear estimate before any work begins. Call (903) 482-4900 to schedule a diagnostic visit.
Do you offer emergency HVAC service in Sherman?
Yes. We offer 24/7 emergency heating and air conditioning service throughout Sherman and Grayson County. When you call after hours, you reach a real person who can get a technician to your home fast. A broken AC in a Sherman summer is not something that can wait until morning.
What HVAC brands do you service in Sherman?
We service all makes and models including Trane, Lennox, Carrier, Daikin, Mitsubishi, Goodman, Rheem, and more. As a Trane Comfort Specialist and Mitsubishi-authorized dealer, we have factory-trained expertise on those brands specifically, but we won’t turn down a job because of the brand on the equipment.
Do you offer HVAC maintenance plans in Sherman?
Yes. Our Adon Care Club is $12 a month and includes two seasonal tune-ups, priority scheduling, repair discounts, no diagnostic fees, and 24/7 emergency response. It’s the most affordable way to keep your system running reliably through Grayson County’s hot summers and cold winters.
What areas of Sherman do you serve?
We serve all of Sherman and the surrounding Grayson County communities including McKinney, Anna, Van Alstyne, Denison, Gunter, Howe, and Tom Bean.
Schedule HVAC Service in Sherman Today
Whether you need same-day AC repair, a new system installed, or just want to get on a maintenance plan before the heat hits, we’re ready to help. Call Adon Complete Air Conditioning and Heating at (903) 482-4900 or schedule online.
Recent Jobs and Reviews in Sherman, TX
Sherman, TX at a glance
Adon Complete Air Conditioning and Heating has completed 10 jobs in Sherman, TX in August 2025.
The most recent job was on August 20, 2025.
Adon Complete Air Conditioning and Heating has completed 138 jobs in Sherman, TX in the last 12 months. The first job there was in March 2020.
Job Locations
Upon arrival, I found that the thermostat would not discover the home’s Wi-Fi and was warm to the touch. I replaced the thermostat and wiring base. I programmed the thermostat to match the original thermostat. Customer spoke about how the kitchen side of the house as hotter than everywhere else. After inspecting, I determined that the best route would be to add an additional plenum with dampers on that side of the house and connect the ducts. This would allow control over individual areas. Currently, the unit has a single metal trunk that runs and splits the ducts inefficiently. I inspected the filter and a connection that we capped off per customer request. To remove the thermostat from nexia, we will need to connect to wifi and remove it on the thermostat. I could not do it on site due to it not discovering the customer’s Wi-Fi.
Upon arrival, I found blockage in the ptrap causing a slow drain. I reached out to Jon to see how he would like to proceed with repair. Jon approved replacement of the ptrap with some alterations to allow more efficient clearing. I performed the work and tested the drain with a half gallon of water, and I allowed the system to run while on site to ensure the system was draining properly.
Installed new 4ton American standard heat pump.
Arrived to unit not cooling g properly. First went to the indoor unit and verified it was on and running but not actually blowing cool air. I proceeded outside and found that the heat pump was also on a running. I diagnosed the system to be low on refrigerant. I was on but not cooling properly due to a leak somewhere in the system. I went inside and found the indoor coil to be frozen over and showed this to our clients. We began discussing repair vs replacement options. They elected to move forward with a replacement of the heat pump system. We are scheduled to preform the change out on Saturday. I collected a $2,170 deposit. Cash discount of -$375.00 to be deducted from total
Sent equipment estimate to Annie for heat pump upgrade or straight ac with electric heat option
Found system still clogged. I cleared it to the best of my ability last time out, but I discovered that the ptrap was blocked again. I cut and removed the ptrap to fully remove all the build up inside of it. I tested the drain will a half gallon of water and verified that it was clear. The ceiling was wet due to the way the emergency pan is hung. There are screw holes on the front side of the pan. This would cause water to drip out if water levels rise high enough. I adjusted the emergency pan float to right next to the screw hole. This will allow the system to shut off before getting too high to drip. Next step will be full drain reconstruction.
Upon arrival, I found unit 4 had a blank thermostat. After further investigation, I found that the emergency drain pan was full of water and the primary drain clogged and incorrectly pitched. I adjusted the drain to the best of my ability to allow a better pitch. My shop vac did not have a long enough cord to remove the water from the pan. I used a bucket and removed the cap off of the emergency pan. This allowed me to remove majority of the water in the pan. I flushed the drain with water and a bit of drain cleaner. The system is fully operational. I could not determine the outdoor unit. Due to the difficult access and the amount of water in the emergency pan, it is going to take longer than normal to clear the drain.
1. Visually inspected condenser coil for debris/ dirty. 2. Inspected condenser fan motor. 3. Inspected condenser fan blades. 4. Inspected/ cleaned wiring connections. 5. Tested compressor/ condenser fan motor capacitor. 6. Checked compressor amp draw. 7. Checked condenser fan motor amp draw. 8. Inspected / replaced return filter. 9. Inspected return plenum for debris/ dirty. 10. Inspected evaporator coil. 11. Inspected blower motor/ blower wheel. 12. Checked blower amp draw. 13. Measured temperature differential from supply to return. 20 degrees measured. 14. Inspected drain lines and treated to prevent blockages 15. Rinsed condenser unit to promote heat exchange 16. Replaced and dated filters Found unit starting with moderately high start amps. Advised homeowner to add hard start kit to prolong system life by lowering wear and tear on unit. Homeowner elected to go forward with the hard start kit next time. Unit in good working order upon departure
Arrived to preform QC on new unit and also install new supply grilles throughout the home. Once the supply grilles were installed I inspected the unit. Our client had concerns about the outdoor unit not being level after recent rain storm. I was able to secure the concrete pad and level it properly. I also took pictures of the attic unit and showed our client all of the items discussed in the estimate. We will call and schedule her first free maintenance in the fall. We also discussed transferring warranty to the new homeowner when/if she decides to sell her home. The unit is cooling properly on departure.
Preformed cooling maintenance. Tested inside units electrical components. All components tested within manufacturer specifications. Treated drain lines with total c. Replaced filter for client 16x25x1. Temperature split across the coil inside is 19 degrees, 54 supply temperature and 73 return temperature. I proceeded outside to test all the electrical components outside, along with run and start amps of the fan motor and compressor motor. Capacitor tested within manufacturer specifications. Contactor was testing on the high side of manufacturer specifications at 20.4 ohms. All run and start amps are within manufacturer specifications. I provided an estimate for a new Contactor. I rinsed outdoor coils. Unit was cooling upon departure.

